RAMB18E1 - 2021.2 English

Vivado Design Suite 7 Series FPGA and Zynq-7000 SoC Libraries Guide (UG953)

Document ID
UG953
Release Date
2021-10-22
Version
2021.2 English

Primitive: 18K-bit Configurable Synchronous Block RAM

Introduction

7 series devices contain several block RAM memories that can be configured as FIFOs, automatic error correction RAM, or general-purpose 36Kb or 18Kb RAM/ROM memories. These block RAM memories offer fast and flexible storage of large amounts of on-chip data. The RAMB18E1 allows access to the block RAM in the 18Kb configuration.

This element can be configured and used as a 1-bit wide by 16K deep to an 18-bit wide by 1024-bit deep true dual port RAM. This element can also be configured as a 36-bit wide by 512 deep simple dual port RAM. Both read and write operations are fully synchronous to the supplied clock(s) to the component. However, the READ and WRITE ports can operate fully independent and asynchronous to each other, accessing the same memory array. When configured in the wider data width modes, byte-enable write operations are possible, and an optional output register can be used to reduce the clock-to-out times of the RAM.

Port Descriptions

Port Direction Width Function
ADDRARDADDR <13:0> Input 14 Port A address input bus/Read address input bus.
ADDRBWRADDR <13:0> Input 14 Port B address input bus/Write address input bus.
CLKARDCLK Input 1 Rising edge port A clock input/Read clock input.
CLKBWRCLK Input 1 Rising edge port B clock input/Write clock input.
DIADI<15:0> Input 16 Port A data input bus/Data input bus addressed by WRADDR. When RAM_MODE="SDP", DIADI is the logical DI<15:0>.
DIBDI<15:0> Input 16 Port B data input bus/Data input bus addressed by WRADDR. When RAM_MODE="SDP", DIBDI is the logical DI<31:16>.
DIPADIP<1:0> Input 2 Port A parity data input bus/Data parity input bus addressed by WRADDR. When RAM_MODE="SDP", DIPADIP is the logical DIP<1:0>.
DIPBDIP<1:0> Input 2 Port B parity data input bus/Data parity input bus addressed by WRADDR. When RAM_MODE="SDP", DIPBDIP is the logical DIP<3:2>.
DOADO<15:0> Output 16 Port A data output bus/Data output bus addressed by RDADDR. When RAM_MODE="SDP", DOADO is the logical DO<15:0>.
DOBDO<15:0> Output 16 Port B data output bus/Data output bus addressed by RDADDR. When RAM_MODE="SDP", DOBDO is the logical DO<31:16>.
DOPADOP<1:0> Output 2 Port A parity data output bus/Data parity output bus addressed by RDADDR. When RAM_MODE="SDP", DOPADOP is the logical DOP<1:0>.
DOPBDOP<1:0> Output 2 Port B parity data output bus/Data parity output bus addressed by RDADDR. When RAM_MODE="SDP", DOPBDOP is the logical DOP<3:2>.
ENARDEN Input 1 Port A RAM enable/Read enable.
ENBWREN Input 1 Port B RAM enable/Write enable.
REGCEAREGCE Input 1 Port A output register clock enable input/Output register clock enable input (valid only when DOA_REG=1).
REGCEB Input 1 Port B output register clock enable (valid only when DOB_REG=1 and RAM_MODE="TDP").
RSTRAMARSTRAM Input 1 Synchronous data latch set/reset to value indicated by SRVAL_A. RSTRAMARSTRAM sets/resets the BRAM data output latch when DO_REG=0 or 1. If DO_REG=1 there is a cycle of latency between the internal data latch node that is reset by RSTRAMARSTRAM and the DO output of the BRAM. This signal resets port A RAM output when RAM_MODE="TDP" and the entire RAM output when RAM_MODE="SDP".
RSTRAMB Input 1 Synchronous data latch set/reset to value indicated by SRVAL_B. RSTRAMB sets/resets the BRAM data output latch when DO_REG=0 or 1. If DO_REG=1 there is a cycle of latency between the internal data latch node that is reset by RSTRAMB and the DO output of the BRAM. Not used when RAM_MODE="SDP".
RSTREGARSTREG Input 1 Synchronous output register set/reset to value indicated by SRVAL_A. RSTREGARSTREG sets/resets the output register when DO_REG=1. RSTREG_PRIORITY_A determines if this signal gets priority over REGCEAREGCE. This signal resets port A output when RAM_MODE="TDP" and the entire output port when RAM_MODE="SDP".
RSTREGB Input 1 Synchronous output register set/reset to value indicated by SRVAL_B. RSTREGB sets/resets the output register when DO_REG=1. RSTREG_PRIORITY_B determines if this signal gets priority over REGCEB. Not used when RAM_MODE="SDP".
WEA<1:0> Input 2 Port A byte-wide write enable. Not used when RAM_MODE="SDP". See User Guide for WEA mapping for different port widths.
WEBWE<3:0> Input 4 Port B byte-wide write enable/Write enable. See User Guide for WEBWE mapping for different port widths.

Design Entry Method

Instantiation Yes
Inference Recommended
IP Catalog Yes
Macro support Yes

Available Attributes

Attribute Type Allowed Values Default Description
RDADDR _COLLISION _HWCONFIG STRING "DELAYED_WRITE", "PERFORMANCE" "DELAYED _WRITE" When set to "PERFORMANCE" allows for higher clock performance (frequency) in READ_FIRST mode. If using the same clock on both ports of the RAM with "PERFORMANCE" mode, the address overlap collision rules apply where in "DELAYED_WRITE" mode, you can safely use the BRAM without incurring collisions.
SIM_COLLISION _CHECK STRING "ALL", "GENERATE_X_ONLY", "NONE", "WARNING_ONLY" "ALL" Allows modification of the simulation behavior so that if a memory collision occurs
  • "ALL" = warning produced and affected outputs/memory go unknown (X)
  • "WARNING_ONLY" = warning produced and affected outputs/memory retain last value
  • "GENERATE_X_ONLY" = no warning and affected outputs/memory go unknown (X)
  • "NONE" = no warning and affected outputs/memory retain last value
Note: Use this setting carefully. Setting it to a value other than "ALL" can mask design problems during simulation.
DOA_REG, DOB_REG DECIMAL 0, 1 0 A value of 1 enables the output registers to the RAM enabling quicker clock-to-out from the RAM at the expense of an added clock cycle of read latency. A value of 0 allows a read in one clock cycle but will result in slower clock-to-out timing. Applies to port A/B in TDP mode and up to 18 lower bits (including parity bits) in SDP mode.
INIT_A, INIT_B HEX 18 bit HEX 18'h00000 Specifies the initial value on the port output after configuration. Applies to Port A/B in TDP mode and up to 18 lower bits (including parity bits) in SDP mode.
INIT_00 to INIT_3F HEX 256 bit HEX All zeros Allows specification of the initial contents of the 16Kb data memory array.
INIT_FILE STRING String representing file name and location None File name of file used to specify initial RAM contents.
INITP_00 to INITP_07 HEX 256 bit HEX All zeros Allows specification of the initial contents of the 2Kb parity data memory array.
RAM_MODE STRING "TDP", "SDP" "TDP" Selects simple dual port (SDP) or true dual port (TDP) mode.
READ_WIDTH_A DECIMAL 0, 1, 2, 4, 9, 18, 36, 72 0 Specifies the desired data width for a read on Port A, including parity bits. This value must be 0 if the Port A is not used. Otherwise, it should be set to the desired port width. In "SDP" mode, this is the read width including parity bits.
READ_WIDTH_B DECIMAL 0, 1, 2, 4, 9, 18 0 Specifies the desired data width for a read on Port B including parity bits. This value must be 0 if the Port B is not used. Otherwise, it should be set to the desired port width. Not used for "SDP" mode.
RSTREG_PRIORITY _A, RSTREG_PRIORITY _B STRING "RSTREG", "REGCE" "RSTREG" Selects register priority for RSTREG or REGCE. Applies to port A/B in TDP mode and up to 18 lower bits (including parity bits) in SDP mode.
SIM_DEVICE STRING "7SERIES" ""7SERIES"" Must be set to "7SERIES" in order to exhibit proper simulation behavior under all conditions.
SRVAL_A, SRVAL_B HEX 18 bit HEX 18'h00000 Specifies the output value of the RAM upon assertion of the synchronous reset (RSTREG) signal.
WRITE_MODE_A, WRITE_MODE_B STRING "WRITE_FIRST", "NO_CHANGE", "READ_FIRST" "WRITE _FIRST" Specifies output behavior of the port being written to.
  • "WRITE_FIRST": Written value appears on output port of the RAM
  • "READ_FIRST": Previous RAM contents for that memory location appear on the output port
  • "NO_CHANGE": Previous value on the output port remains the same.
When RAM_MODE="SDP", WRITE_MODE can not be set to "NO_CHANGE". For simple dual port implementations you should set this attribute to "READ_FIRST" if using the same clock on both ports, or set it to "WRITE_FIRST" if using different clocks. This generally yields an improved collision or address overlap behavior.
WRITE_WIDTH_A DECIMAL 0, 1, 2, 4, 9, 18 0 Specifies the desired data width for a write to Port A including parity bits. This value must be 0 if the port is not used. Otherwise should be set to the desired write width. Not used in SDP mode.
WRITE_WIDTH_B DECIMAL 0, 1, 2, 4, 9, 18, 36, 72 0 Specifies the desired data width for a write to Port B including parity bits. This value must be 0 if the port is not used. Otherwise should be set to the desired write width. In SDP mode, this is the write width including parity bits.

VHDL Instantiation Template

Unless they already exist, copy the following two statements and paste them before the entity declaration.
Library UNISIM;
use UNISIM.vcomponents.all;

-- RAMB18E1: 18K-bit Configurable Synchronous Block RAM
--           7 Series
-- Xilinx HDL Language Template, version 2021.2

RAMB18E1_inst : RAMB18E1
generic map (
   -- Address Collision Mode: "PERFORMANCE" or "DELAYED_WRITE"
   RDADDR_COLLISION_HWCONFIG => "DELAYED_WRITE",
   -- Collision check: Values ("ALL", "WARNING_ONLY", "GENERATE_X_ONLY" or "NONE")
   SIM_COLLISION_CHECK => "ALL",
   -- DOA_REG, DOB_REG: Optional output register (0 or 1)
   DOA_REG => 0,
   DOB_REG => 0,
   -- INITP_00 to INITP_07: Initial contents of parity memory array
   INITP_00 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_01 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_02 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_03 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_04 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_05 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_06 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INITP_07 => X"0000000000000000000000000000000000000000000000000000000000000000",
   -- INIT_00 to INIT_3F: Initial contents of data memory array
   INIT_00 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_01 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_02 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_03 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_04 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_05 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_06 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_07 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_08 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_09 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_0A => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_0B => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_0C => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_0D => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_0E => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_0F => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_10 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_11 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_12 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_13 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_14 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_15 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_16 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_17 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_18 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_19 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_1A => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_1B => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_1C => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_1D => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_1E => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_1F => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_20 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_21 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_22 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_23 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_24 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_25 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_26 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_27 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_28 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_29 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_2A => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_2B => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_2C => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_2D => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_2E => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_2F => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_30 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_31 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_32 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_33 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_34 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_35 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_36 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_37 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_38 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_39 => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_3A => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_3B => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_3C => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_3D => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_3E => X"0000000000000000000000000000000000000000000000000000000000000000",
   INIT_3F => X"0000000000000000000000000000000000000000000000000000000000000000",
   -- INIT_A, INIT_B: Initial values on output ports
   INIT_A => X"00000",
   INIT_B => X"00000",
   -- Initialization File: RAM initialization file
   INIT_FILE => "NONE",
   -- RAM Mode: "SDP" or "TDP"
   RAM_MODE => "TDP",
   -- READ_WIDTH_A/B, WRITE_WIDTH_A/B: Read/write width per port
   READ_WIDTH_A => 0,                                                               -- 0-72
   READ_WIDTH_B => 0,                                                               -- 0-18
   WRITE_WIDTH_A => 0,                                                              -- 0-18
   WRITE_WIDTH_B => 0,                                                              -- 0-72
   -- RSTREG_PRIORITY_A, RSTREG_PRIORITY_B: Reset or enable priority ("RSTREG" or "REGCE")
   RSTREG_PRIORITY_A => "RSTREG",
   RSTREG_PRIORITY_B => "RSTREG",
   -- SRVAL_A, SRVAL_B: Set/reset value for output
   SRVAL_A => X"00000",
   SRVAL_B => X"00000",
   -- Simulation Device: Must be set to "7SERIES" for simulation behavior
   SIM_DEVICE => "7SERIES",
   -- WriteMode: Value on output upon a write ("WRITE_FIRST", "READ_FIRST", or "NO_CHANGE")
   WRITE_MODE_A => "WRITE_FIRST",
   WRITE_MODE_B => "WRITE_FIRST"
)
port map (
   -- Port A Data: 16-bit (each) output: Port A data
   DOADO => DOADO,                 -- 16-bit output: A port data/LSB data
   DOPADOP => DOPADOP,             -- 2-bit output: A port parity/LSB parity
   -- Port B Data: 16-bit (each) output: Port B data
   DOBDO => DOBDO,                 -- 16-bit output: B port data/MSB data
   DOPBDOP => DOPBDOP,             -- 2-bit output: B port parity/MSB parity
   -- Port A Address/Control Signals: 14-bit (each) input: Port A address and control signals (read port
   -- when RAM_MODE="SDP")
   ADDRARDADDR => ADDRARDADDR,     -- 14-bit input: A port address/Read address
   CLKARDCLK => CLKARDCLK,         -- 1-bit input: A port clock/Read clock
   ENARDEN => ENARDEN,             -- 1-bit input: A port enable/Read enable
   REGCEAREGCE => REGCEAREGCE,     -- 1-bit input: A port register enable/Register enable
   RSTRAMARSTRAM => RSTRAMARSTRAM, -- 1-bit input: A port set/reset
   RSTREGARSTREG => RSTREGARSTREG, -- 1-bit input: A port register set/reset
   WEA => WEA,                     -- 2-bit input: A port write enable
   -- Port A Data: 16-bit (each) input: Port A data
   DIADI => DIADI,                 -- 16-bit input: A port data/LSB data
   DIPADIP => DIPADIP,             -- 2-bit input: A port parity/LSB parity
   -- Port B Address/Control Signals: 14-bit (each) input: Port B address and control signals (write port
   -- when RAM_MODE="SDP")
   ADDRBWRADDR => ADDRBWRADDR,     -- 14-bit input: B port address/Write address
   CLKBWRCLK => CLKBWRCLK,         -- 1-bit input: B port clock/Write clock
   ENBWREN => ENBWREN,             -- 1-bit input: B port enable/Write enable
   REGCEB => REGCEB,               -- 1-bit input: B port register enable
   RSTRAMB => RSTRAMB,             -- 1-bit input: B port set/reset
   RSTREGB => RSTREGB,             -- 1-bit input: B port register set/reset
   WEBWE => WEBWE,                 -- 4-bit input: B port write enable/Write enable
   -- Port B Data: 16-bit (each) input: Port B data
   DIBDI => DIBDI,                 -- 16-bit input: B port data/MSB data
   DIPBDIP => DIPBDIP              -- 2-bit input: B port parity/MSB parity
);

-- End of RAMB18E1_inst instantiation

Verilog Instantiation Template


// RAMB18E1: 18K-bit Configurable Synchronous Block RAM
//           7 Series
// Xilinx HDL Language Template, version 2021.2

RAMB18E1 #(
   // Address Collision Mode: "PERFORMANCE" or "DELAYED_WRITE"
   .RDADDR_COLLISION_HWCONFIG("DELAYED_WRITE"),
   // Collision check: Values ("ALL", "WARNING_ONLY", "GENERATE_X_ONLY" or "NONE")
   .SIM_COLLISION_CHECK("ALL"),
   // DOA_REG, DOB_REG: Optional output register (0 or 1)
   .DOA_REG(0),
   .DOB_REG(0),
   // INITP_00 to INITP_07: Initial contents of parity memory array
   .INITP_00(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_01(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_02(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_03(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_04(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_05(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_06(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INITP_07(256'h0000000000000000000000000000000000000000000000000000000000000000),
   // INIT_00 to INIT_3F: Initial contents of data memory array
   .INIT_00(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_01(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_02(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_03(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_04(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_05(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_06(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_07(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_08(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_09(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_0A(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_0B(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_0C(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_0D(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_0E(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_0F(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_10(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_11(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_12(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_13(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_14(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_15(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_16(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_17(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_18(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_19(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_1A(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_1B(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_1C(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_1D(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_1E(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_1F(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_20(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_21(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_22(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_23(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_24(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_25(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_26(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_27(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_28(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_29(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_2A(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_2B(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_2C(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_2D(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_2E(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_2F(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_30(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_31(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_32(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_33(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_34(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_35(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_36(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_37(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_38(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_39(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_3A(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_3B(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_3C(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_3D(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_3E(256'h0000000000000000000000000000000000000000000000000000000000000000),
   .INIT_3F(256'h0000000000000000000000000000000000000000000000000000000000000000),
   // INIT_A, INIT_B: Initial values on output ports
   .INIT_A(18'h00000),
   .INIT_B(18'h00000),
   // Initialization File: RAM initialization file
   .INIT_FILE("NONE"),
   // RAM Mode: "SDP" or "TDP"
   .RAM_MODE("TDP"),
   // READ_WIDTH_A/B, WRITE_WIDTH_A/B: Read/write width per port
   .READ_WIDTH_A(0),                                                                 // 0-72
   .READ_WIDTH_B(0),                                                                 // 0-18
   .WRITE_WIDTH_A(0),                                                                // 0-18
   .WRITE_WIDTH_B(0),                                                                // 0-72
   // RSTREG_PRIORITY_A, RSTREG_PRIORITY_B: Reset or enable priority ("RSTREG" or "REGCE")
   .RSTREG_PRIORITY_A("RSTREG"),
   .RSTREG_PRIORITY_B("RSTREG"),
   // SRVAL_A, SRVAL_B: Set/reset value for output
   .SRVAL_A(18'h00000),
   .SRVAL_B(18'h00000),
   // Simulation Device: Must be set to "7SERIES" for simulation behavior
   .SIM_DEVICE("7SERIES"),
   // WriteMode: Value on output upon a write ("WRITE_FIRST", "READ_FIRST", or "NO_CHANGE")
   .WRITE_MODE_A("WRITE_FIRST"),
   .WRITE_MODE_B("WRITE_FIRST")
)
RAMB18E1_inst (
   // Port A Data: 16-bit (each) output: Port A data
   .DOADO(DOADO),                 // 16-bit output: A port data/LSB data
   .DOPADOP(DOPADOP),             // 2-bit output: A port parity/LSB parity
   // Port B Data: 16-bit (each) output: Port B data
   .DOBDO(DOBDO),                 // 16-bit output: B port data/MSB data
   .DOPBDOP(DOPBDOP),             // 2-bit output: B port parity/MSB parity
   // Port A Address/Control Signals: 14-bit (each) input: Port A address and control signals (read port
   // when RAM_MODE="SDP")
   .ADDRARDADDR(ADDRARDADDR),     // 14-bit input: A port address/Read address
   .CLKARDCLK(CLKARDCLK),         // 1-bit input: A port clock/Read clock
   .ENARDEN(ENARDEN),             // 1-bit input: A port enable/Read enable
   .REGCEAREGCE(REGCEAREGCE),     // 1-bit input: A port register enable/Register enable
   .RSTRAMARSTRAM(RSTRAMARSTRAM), // 1-bit input: A port set/reset
   .RSTREGARSTREG(RSTREGARSTREG), // 1-bit input: A port register set/reset
   .WEA(WEA),                     // 2-bit input: A port write enable
   // Port A Data: 16-bit (each) input: Port A data
   .DIADI(DIADI),                 // 16-bit input: A port data/LSB data
   .DIPADIP(DIPADIP),             // 2-bit input: A port parity/LSB parity
   // Port B Address/Control Signals: 14-bit (each) input: Port B address and control signals (write port
   // when RAM_MODE="SDP")
   .ADDRBWRADDR(ADDRBWRADDR),     // 14-bit input: B port address/Write address
   .CLKBWRCLK(CLKBWRCLK),         // 1-bit input: B port clock/Write clock
   .ENBWREN(ENBWREN),             // 1-bit input: B port enable/Write enable
   .REGCEB(REGCEB),               // 1-bit input: B port register enable
   .RSTRAMB(RSTRAMB),             // 1-bit input: B port set/reset
   .RSTREGB(RSTREGB),             // 1-bit input: B port register set/reset
   .WEBWE(WEBWE),                 // 4-bit input: B port write enable/Write enable
   // Port B Data: 16-bit (each) input: Port B data
   .DIBDI(DIBDI),                 // 16-bit input: B port data/MSB data
   .DIPBDIP(DIPBDIP)              // 2-bit input: B port parity/MSB parity
);

// End of RAMB18E1_inst instantiation

Related Information

  • See the 7 Series FPGAs Memory Resources User Guide (UG473).