RAM64X1S_1 - 2021.2 English

Vivado Design Suite 7 Series FPGA and Zynq-7000 SoC Libraries Guide (UG953)

Document ID
UG953
Release Date
2021-10-22
Version
2021.2 English

Primitive: 64-Deep by 1-Wide Static Synchronous RAM with Negative-Edge Clock

Introduction

This design element is a 64-bit deep by 1-bit wide static random access memory with synchronous write capability. When the write enable is Low, transitions on the write clock (WCLK) are ignored and data stored in the RAM is not affected. When (WE) is High, any negative transition on (WCLK) loads the data on the data input (D) into the memory cell selected by the 6-bit address (A5:A0). For predictable performance, address and data inputs must be stable before a High-to-Low (WCLK) transition. This RAM block assumes an active-Low (WCLK). However, (WCLK) can be active-High or active-Low. Any inverter placed on the (WCLK) input net is absorbed into the block.

The signal output on the data output pin (O) is the data that is stored in the memory cell defined by the values on the address pins.

You can use the INIT attribute to specify the initial contents of the RAM. If left unspecified, the initial contents default to all zeros.

Logic Table

Inputs Outputs
WE (mode) WCLK D O
0 (read) X X Data
1 (read) 0 X Data
1 (read) 1 X Data
1 (write) D D
1 (read) X Data

Data = memory cell addressed by bits A5:A0

Design Entry Method

Instantiation Yes
Inference Recommended
IP Catalog No
Macro support No

Available Attributes

Attribute Type Allowed Values Default Description
INIT HEX Any 64-bit value All zeros Specifies the initial contents of the RAM.

VHDL Instantiation Template

Unless they already exist, copy the following two statements and paste them before the entity declaration.
Library UNISIM;
use UNISIM.vcomponents.all;

-- RAM64X1S_1: 64 x 1 negative edge write, asynchronous read single-port distributed RAM (Mapped to SliceM LUT6)
--             7 Series
-- Xilinx HDL Language Template, version 2021.2

RAM64X1S_1_inst : RAM64X1S_1
generic map (
   INIT => X"0000000000000000")
port map (
   O => O,        -- 1-bit data output
   A0 => A0,      -- Address[0] input bit
   A1 => A1,      -- Address[1] input bit
   A2 => A2,      -- Address[2] input bit
   A3 => A3,      -- Address[3] input bit
   A4 => A4,      -- Address[4] input bit
   A5 => A5,      -- Address[5] input bit
   D => D,        -- 1-bit data input
   WCLK => WCLK,  -- Write clock input
   WE => WE       -- Write enable input
);

-- End of RAM64X1S_1_inst instantiation

Verilog Instantiation Template


// RAM64X1S_1: 64 x 1 negative edge write, asynchronous read single-port
//             distributed RAM (Mapped to a SliceM LUT6)
//             7 Series
// Xilinx HDL Language Template, version 2021.2

RAM64X1S_1 #(
   .INIT(64'h0000000000000000) // Initial contents of RAM
) RAM64X1S_1_inst (
   .O(O),        // 1-bit data output
   .A0(A0),      // Address[0] input bit
   .A1(A1),      // Address[1] input bit
   .A2(A2),      // Address[2] input bit
   .A3(A3),      // Address[3] input bit
   .A4(A4),      // Address[4] input bit
   .A5(A5),      // Address[5] input bit
   .D(D),        // 1-bit data input
   .WCLK(WCLK),  // Write clock input
   .WE(WE)       // Write enable input
);

// End of RAM64X1S_1_inst instantiation

Related Information

  • See the 7 Series FPGAs Configurable Logic Block User Guide (UG474).