IDDR - 2021.2 English

Vivado Design Suite 7 Series FPGA and Zynq-7000 SoC Libraries Guide (UG953)

Document ID
UG953
Release Date
2021-10-22
Version
2021.2 English

Primitive: Input Double Data-Rate Register

Introduction

This design element is a dedicated input register designed to receive external double data rate (DDR) signals into Xilinx® FPGAs. The IDDR is available with modes that present the data to the FPGA fabric at the time and clock edge they are captured, or on the same clock edge. This feature allows you to avoid additional timing complexities and resource usage.

  • OPPOSITE_EDGE mode Data is recovered in the classic DDR methodology. Given a DDR data and clock at pin D and C respectively, Q1 changes after every positive edge of clock C, and Q2 changes after every negative edge of clock C.

  • SAME_EDGE mode Data is still recovered by opposite edges of clock C. However, an extra register has been placed behind the negative edge data register. This extra register is clocked with positive clock edge of clock signal C. As a result, DDR data is now presented into the FPGA fabric at the same clock edge. However, because of this feature, the data pair appears to be "separated." Q1 and Q2 no longer have pair 1 and 2. Instead, the first pair presented is Pair 1 and DONT_CARE, followed by Pair 2 and 3 at the next clock cycle.

  • SAME_EDGE_PIPELINED mode Recovers data in a similar fashion as the SAME_EDGE mode. In order to avoid the "separated" effect of the SAME_EDGE mode, an extra register has been placed in front of the positive edge data register. A data pair now appears at the Q1 and Q2 pin at the same time. However, using this mode costs you an additional cycle of latency for Q1 and Q2 signals to change.

IDDR also works with the SelectIO™ features, such as the IDELAYE2.

Note: For high speed interfaces, you can use the IDDR_2CLK to specify two independent clocks to capture the data. Use this component when the performance requirements of the IDDR are not adequate, because the IDDR_2CLK requires more clocking resources and can imply placement restrictions that are not necessary when using the IDDR component.

Port Descriptions

Port Direction Width Function
Q1 - Q2 Output 1

The IDDR output pins that connect to the FPGA fabric.

C Input 1

Clock input pin.

CE Input 1

The enable pin affects the loading of data into the DDR flip-flop. When Low, clock transitions are ignored and new data is not loaded into the DDR flip-flop. CE must be high to load new data into the flip-flop.

D Input 1

Input to the IDDR module.This pin connects to a top-level input or bidirectional port, and IDELAYE2 configured for an input delay or to an appropriate input or bidirectional buffer.

R Input 1

Active-High reset forcing Q1 and Q2 to a logic zero. Can be synchronous or asynchronous based on the SRTYPE attribute.

S Input 1

Active-High reset forcing Q1 and Q2 to a logic one. Can be synchronous or asynchronous based on the SRTYPE attribute.

Note: You cannot have an active set and an active reset in this component. One or both of the signals R and S must be tied to ground.

Design Entry Method

Instantiation Recommended
Inference No
IP Catalog Yes
Macro support No

Available Attributes

Attribute Type Allowed Values Default Description
DDR_CLK_EDGE STRING "OPPOSITE_EDGE", "SAME_EDGE", "SAME_EDGE_PIPELINED" "OPPOSITE_EDGE" Sets the IDDR mode of operation with respect to clock edge.
INIT_Q1 BINARY 0, 1 0 Initial value on the Q1 pin after configuration startup or when GSR is asserted.
INIT_Q2 BINARY 0, 1 0 Initial value on the Q2 pin after configuration startup or when GSR is asserted.
SRTYPE STRING "SYNC" or "ASYNC" "SYNC" Set/reset type selection. "SYNC" specifies the behavior of the reset (R) and set (S) pins to be synchronous to the positive edge of the C clock pin. "ASYNC" specifies an asynchronous set/reset function.

VHDL Instantiation Template

Unless they already exist, copy the following two statements and paste them before the entity declaration.
Library UNISIM;
use UNISIM.vcomponents.all;

-- IDDR: Double Data Rate Input Register with Set, Reset
--       and Clock Enable.
--       7 Series
-- Xilinx HDL Language Template, version 2021.2

IDDR_inst : IDDR
generic map (
   DDR_CLK_EDGE => "OPPOSITE_EDGE", -- "OPPOSITE_EDGE", "SAME_EDGE"
                                    -- or "SAME_EDGE_PIPELINED"
   INIT_Q1 => '0', -- Initial value of Q1: '0' or '1'
   INIT_Q2 => '0', -- Initial value of Q2: '0' or '1'
   SRTYPE => "SYNC") -- Set/Reset type: "SYNC" or "ASYNC"
port map (
   Q1 => Q1, -- 1-bit output for positive edge of clock
   Q2 => Q2, -- 1-bit output for negative edge of clock
   C => C,   -- 1-bit clock input
   CE => CE, -- 1-bit clock enable input
   D => D,   -- 1-bit DDR data input
   R => R,   -- 1-bit reset
   S => S    -- 1-bit set
   );

-- End of IDDR_inst instantiation

Verilog Instantiation Template


// IDDR: Input Double Data Rate Input Register with Set, Reset
//       and Clock Enable.
//       7 Series
// Xilinx HDL Language Template, version 2021.2

IDDR #(
   .DDR_CLK_EDGE("OPPOSITE_EDGE"), // "OPPOSITE_EDGE", "SAME_EDGE"
                                   //    or "SAME_EDGE_PIPELINED"
   .INIT_Q1(1'b0), // Initial value of Q1: 1'b0 or 1'b1
   .INIT_Q2(1'b0), // Initial value of Q2: 1'b0 or 1'b1
   .SRTYPE("SYNC") // Set/Reset type: "SYNC" or "ASYNC"
) IDDR_inst (
   .Q1(Q1), // 1-bit output for positive edge of clock
   .Q2(Q2), // 1-bit output for negative edge of clock
   .C(C),   // 1-bit clock input
   .CE(CE), // 1-bit clock enable input
   .D(D),   // 1-bit DDR data input
   .R(R),   // 1-bit reset
   .S(S)    // 1-bit set
);

// End of IDDR_inst instantiation

Related Information

  • See the 7 Series FPGA SelectIO Resources User Guide (UG471).