[Figure 1, area of callouts 17 and 18]
The following table defines the power and status LEDs. For user controlled GPIO LED details, see User I/O.
Ref. Des. | Schematic Net Name | LED Color | Description |
---|---|---|---|
DS1 | MIO23_LED | Green | RFSoC U1 Bank 500 GPIO LED |
DS2 | PS_INIT_B | Green/ Red | Green: FPGA initialization was successful Red: FPGA initialization is in progress |
DS3 | PS_DONE | Green | RFSoC U1 bit file download is complete |
DS4 | PS_RESET_B | Red | POR U5 asserts RESET_B low when any of the monitored voltages (IN_) falls below its respective threshold, any EN_ goes low, or MR is asserted. |
DS5 | PS_ERR_OUT | Red | PS error out is asserted for accidental loss of power, an error in the PMU that holds the CSU in reset, or an exception in the PMU. |
DS6 | PS_ERR_STATUS | Red | PS error status indicates a secure lockdown state. Alternatively, it can be used by the PMU firmware to indicate system status. |
DS7 | USB3 MIC2544 U7 FLG | Green | PS USB 3.0 ULPI VBUS Power Error |
P1-R | ENET_LED_0 | Green | EPHY U33 link established (all speeds) (RJ45 bezel right) |
DS8 | ENET_LED_1 | Green | EPHY U33 1000BASE-T link established |
P1-L | ENET_LED_2 | Green | EPHY U33 link activity (RJ45 bezel left) |
DS9 | MSP430_LED0 | Blue | MSP430 U38 GPIO LED |
DS10 | MSP430_LED1 | Green | MSP430 U38 GPIO LED |
DS19 | VCC12_SW | Green | 12VDC Power ON |
DS20 | VCCINT_PG | Green | VCCINT 0.85VDC Power ON |
DS21 | VCCINT_IO_BRAM_PS_PG | Green | VCCPSINTFP/LP/BRAM/IO 0.85VDC Power ON |
DS22 | VCC1V8_PG | Green | VCC1V8 1.8VDC Power ON |
DS23 | VCC1V2_PG | Green | VCC1V2 1.2VDC Power ON |
DS24 | VADJ_FMC_PG | Green | VADJ_FMC 1.8VDC (Nom.) Power ON |
DS25 | MGTAVCC_PG | Green | MGTAVCC 0.9VDC Power ON |
DS26 | DAC_AVCC_PG | Green | ADC_AVCC 0.925V Power ON |
DS27 | MGT1V2_PG | Green | MGT1V2 1.2VDC Power ON |
DS29 | MGTRAVCC_PG | Green | MGTRAVCC 0.85VDC Power ON |
DS30 | MGT1V8_PG | Green | MGT1V8 1.8VDC Power ON |
DS31 | VCCINT_AMS_PG | Green | VCCINT_AMS 0.85VDC Power ON |
DS32 | ADC_AVCC_PG | Green | ADC_AVCC 0.925VDC Power ON |
DS34 | ADC_AVCCAUX_PG | Green | ADC_AVCCAUX 1.8VDC Power ON |
DS36 | DAC_AVTT_PG | Green | DAC_AVTT 2.5VDC Power ON |
DS37 | UTIL_1V13_PG | Green | UTIL_1V13 1.13VDC Power ON |
DS38 | UTIL_2V5_PG | Green | UTIL_2V5 2.5VDC Power ON |
DS39 | UTIL_3V3_PG | Green | UTIL_3V3 3.3VDC Power ON |
DS40 | UTIL_5V0_PG | Green | UTIL_5V0 5VDC Power ON |
DS41 | PS_DDR4_VTERM_0V60_PG | Green | PS_DDR4_VTERM 0.6VDC Power ON |
DS42 | PL_C0_DDR4_VTERM_0V60_PG | Green | PL_C0_DDR4_VTERM 0.6VDC Power ON |
DS43 | PL_C1_DDR4_VTERM_0V60_PG | Green | PL_C1_DDR4_VTERM 0.6VDC Power ON |
DS44 | DAC_AVCCAUX_ON | Green | DAC_AVCCAUX 1.8VDC Power ON |
DS46 | RGB_[R,G,B]_LED_0 | R,G,B | USER GPIO RGB LED_0 |
DS47 | RGB_[R,G,B]_LED_1 | R,G,B | USER GPIO RGB LED_1 |
DS48 | RGB_[R,G,B]_LED_2 | R,G,B | USER GPIO RGB LED_2 |
DS49 | RGB_[R,G,B]_LED_3 | R,G,B | USER GPIO RGB LED_3 |
DS50 | RGB_[R,G,B]_LED_4 | R,G,B | USER GPIO RGB LED_4 |
DS51 | RGB_[R,G,B]_LED_5 | R,G,B | USER GPIO RGB LED_5 |
DS52 | RGB_[R,G,B]_LED_6 | R,G,B | USER GPIO RGB LED_6 |
DS53 | RGB_[R,G,B]_LED_7 | R,G,B | USER GPIO RGB LED_7 |
The following figure shows the GPIO and power status LED areas of the board.
Figure 1. GPIO and Power Status LED areas