RXTX_BITSLICE - 2022.1 English

Primitive: RXTX_BITSLICE for bidirectional I/O using Native Mode

PRIMITIVE_GROUP: I/O
PRIMITIVE_SUBGROUP: BITSLICE
Families: UltraScale, UltraScale+

Introduction

In native mode, the RXTX_BITSLICE performs both functions of an RX_BITSLICE and TX_BITSLICE for bidirectional I/O.

Port Descriptions

Port	Direction	Width	Function
D<7:0>	Input	8	Data from device logic.
DATAIN	Input	1	Input signal from IOBUF.
FIFO_EMPTY	Output	1	FIFO empty flag for the FIFO of this bit.
FIFO_RD_CLK	Input	1	FIFO read clock for the FIFO of this bit.
FIFO_RD_EN	Input	1	FIFO read enable for the FIFO of this bit.
FIFO_WRCLK_OUT	Output	1	FIFO source synchronous write clock out to the device logic. Only valid for RX_BITSLICE 0. Currently not supported, do not connect.
O	Output	1	Serialized output going to output buffer.
Q<7:0>	Output	8	Registered output data from FIFO.
RX_BIT_CTRL_IN<39:0>	Input	40	RX Input bus from BITSLICE_CONTROL.
RX_BIT_CTRL_OUT<39:0>	Output	40	RX Output bus to BITSLICE_CONTROL.
RX_CE	Input	1	Clock enable for RXTX_BITSLICE IDELAY register clock.
RX_CLK	Input	1	RX Clock used to sample LOAD, CE, INC.
RX_CNTVALUEIN<8:0>	Input	9	RX Counter value from internal device logic for tap value to be loaded dynamically.
RX_CNTVALUEOUT<8:0>	Output	9	RX Counter value from internal device logic for tap value to be loaded dynamically.
RX_EN_VTC	Input	1	RX Enable to keep stable delay over VT when set to HIGH. VT compensation disabled when set to LOW.
RX_INC	Input	1	RX Increment the current delay tap setting.
RX_LOAD	Input	1	RX Load the CNTVALUEIN tap setting.
RX_RST	Input	1	RX Asynchronous assert, synchronous deassert for RXTX_BITSLICE ISERDES.
RX_RST_DLY	Input	1	RX Reset the internal DELAY value to DELAY_VALUE.
T	Input	1	Legacy T byte input from device logic.
TBYTE_IN	Input	1	Byte group 3-state input from TX_BITSLICE_TRI.
T_OUT	Output	1	Byte group 3-state output.
TX_BIT_CTRL_IN<39:0>	Input	40	TX Input bus from BITSLICE_CONTROL.
TX_BIT_CTRL_OUT<39:0>	Output	40	Output bus to BITSLICE_CONTROL for TX.
TX_CE	Input	1	Clock enable for RXTX_BITSLICE ODELAY register clock.
TX_CLK	Input	1	TX Clock used to sample LOAD, CE, INC.
TX_CNTVALUEIN<8:0>	Input	9	TX Counter value from internal device logic for tap value to be loaded dynamically.
TX_CNTVALUEOUT<8:0>	Output	9	TX Counter value to going the internal device logic for monitoring tap value.
TX_EN_VTC	Input	1	TX Enable to keep stable delay over VT when set to HIGH. VT compensation disabled when set to LOW.
TX_INC	Input	1	TX Increment the current delay tap setting.
TX_LOAD	Input	1	TX Load the CNTVALUEIN tap setting.
TX_RST	Input	1	TX Asynchronous assert, synchronous deassert for RXTX_BITSLICE OSERDES.
TX_RST_DLY	Input	1	TX Reset the internal DELAY value to DELAY_VALUE.

Design Entry Method

Instantiation	Yes
Inference	No
IP and IP Integrator Catalog	Yes

Available Attributes

Attribute	Type	Allowed Values	Default	Description
ENABLE_PRE_EMPHASIS	STRING	"FALSE", "TRUE"	"FALSE"	Used in conjunction with IOB to Enable the pre-emphasis.
FIFO_SYNC_MODE	STRING	"FALSE", "TRUE"	"FALSE"	Attribute defining the relationship between FIFO_WRCLK_OUT and FIFO_RD_CLK. Always set this attribute to FALSE. TRUE is reserved for later use.
INIT	BINARY	1'b1, 1'b0	1'b1	Defines initial O value
IS_RX_CLK_INVERTED	BINARY	1'b0 to 1'b1	1'b0	Specifies whether the clock RX_CLK pin is active-High or active-Low.
IS_RX_RST_DLY_INVERTED	BINARY	1'b0 to 1'b1	1'b0	Specifies whether the reset RX_RST_DLY pin is active-High or active-Low.
IS_RX_RST_INVERTED	BINARY	1'b0 to 1'b1	1'b0	Specifies whether the reset RX_RST pin is active-High or active-Low.
IS_TX_CLK_INVERTED	BINARY	1'b0 to 1'b1	1'b0	Specifies whether the clock TX_CLK pin is active-High or active-Low.
IS_TX_RST_DLY_INVERTED	BINARY	1'b0 to 1'b1	1'b0	Specifies whether the reset TX_RST_DLY pin is active-High or active-Low.
IS_TX_RST_INVERTED	BINARY	1'b0 to 1'b1	1'b0	Specifies whether the reset TX_RST pin is active-High or active-Low.
RX_DATA_TYPE	STRING	"DATA", "CLOCK", "DATA_AND_CLOCK", "SERIAL"	"DATA"	Defines whether the RX input pin is carrying a clock signal, a data signal, or clock signal that is also used as data.
RX_DATA_WIDTH	DECIMAL	8, 4	8	Defines the width of the serial-to-parallel converter. Legal data widths are 4 and 8.
RX_DELAY_FORMAT	STRING	"TIME", "COUNT"	"TIME"	Sets the units of DELAY_VALUE of the RXTX_BITSLICE IDELAY. Use TIME when DELAY_TYPE is FIXED. Use COUNT when DELAY_TYPE is VARIABLE or VAR_LOAD. "TIME": RXTX_BITSLICE IDELAY DELAY_VALUE is specified in ps "COUNT": RXTX_BITSLICE IDELAY DELAY_VALUE is specified in taps
RX_DELAY_TYPE	STRING	"FIXED", "VARIABLE", "VAR_LOAD"	"FIXED"	Sets the type of RX tap delay line. "FIXED": Sets a static delay value. "VARIABLE": Dynamically adjust (increment/decrement) delay value. "VAR_LOAD": Dynamically loads tap values.
RX_DELAY_VALUE	DECIMAL	0 to 1250	0	Specifies the RX fixed delay in ps when using FIXED DELAY_TYPE. Specifies RX value upon reset when using VARIABLE or VAR_LOAD.
RX_REFCLK_FREQUENCY	1 significant digit FLOAT	200.0 to 2667.0	300.0	Specification of the RX reference clock frequency in MHz.
RX_UPDATE_MODE	STRING	"ASYNC", "MANUAL", "SYNC"	"ASYNC"	"ASYNC": Updates are increases or decreases to the delay value independent of the data being received. "SYNC": Updates require that data input transitions to synchronously update the delay with the data input edges. "MANUAL": Updates take effect when both LOAD and CE are asserted after the LOAD and CNTVALUEIN signals are used to load the new CNTVALUE.
SIM_DEVICE	STRING	"7SERIES", "ULTRASCALE"	"ULTRASCALE"	Set the device version for simulation functionality.
TBYTE_CTL	STRING	"TBYTE_IN", "T"	"TBYTE_IN"	Select between T and TBYTE_IN inputs in OSERDES mode only
TX_DATA_WIDTH	DECIMAL	8, 4	8	Defines the parallel data input width. Legal values are 4 and 8.
TX_DELAY_FORMAT	STRING	"TIME", "COUNT"	"TIME"	Sets the units of DELAY_VALUE of the RXTX_BITSLICE ODELAY. Use TIME when DELAY_TYPE is FIXED. Use COUNT when DELAY_TYPE is VARIABLE or VAR_LOAD. "TIME": RXTX_BITSLICE ODELAY DELAY_VALUE is specified in ps. "COUNT": RXTX_BITSLICE ODELAY DELAY_VALUE is specified in taps.
TX_DELAY_TYPE	STRING	"FIXED", "VARIABLE", "VAR_LOAD"	"FIXED"	Sets the type of TX tap delay line. "FIXED": Sets a static delay value. "VARIABLE": Dynamically adjust (increment/decrement) delay value. "VAR_LOAD": Dynamically loads tap values.
TX_DELAY_VALUE	DECIMAL	0 to 1250	0	Specifies the TX fixed delay in ps when using FIXED DELAY_TYPE. Specifies TX value upon reset when using VARIABLE or VAR_LOAD.
TX_OUTPUT_PHASE_90	STRING	"FALSE", "TRUE"	"FALSE"	Delays the output phase by 90-degrees.
TX_REFCLK_FREQUENCY	1 significant digit FLOAT	200.0 to 2667.0	300.0	Specification of the TX reference clock frequency in MHz.
TX_UPDATE_MODE	STRING	"ASYNC", "MANUAL", "SYNC"	"ASYNC"	"ASYNC": Updates are increments or decrements to the delay value independent of the data being received. "SYNC": Updates require that input data transitions to synchronously update the delay with the data input edges. "MANUAL": Updates take effect when both LOAD and CE are asserted after the LOAD and CNTVALUEIN signals are used to load the new CNTVALUE.

VHDL Instantiation Template

Unless they already exist, copy the following two statements and paste them before the entity declaration.

Library UNISIM;
use UNISIM.vcomponents.all;


-- RXTX_BITSLICE: RXTX_BITSLICE for bidirectional I/O using Native Mode
--                UltraScale
-- Xilinx HDL Language Template, version 2022.1

RXTX_BITSLICE_inst : RXTX_BITSLICE
generic map (
   ENABLE_PRE_EMPHASIS => "FALSE",  -- Enable the pre-emphasis
   FIFO_SYNC_MODE => "FALSE",       -- Always set to FALSE. TRUE is reserved for later use.
   INIT => '1',                     -- Defines initial O value
   IS_RX_CLK_INVERTED => '0',       -- Optional inversion for RX_CLK
   IS_RX_RST_DLY_INVERTED => '0',   -- Optional inversion for RX_RST_DLY
   IS_RX_RST_INVERTED => '0',       -- Optional inversion for RX_RST
   IS_TX_CLK_INVERTED => '0',       -- Optional inversion for TX_CLK
   IS_TX_RST_DLY_INVERTED => '0',   -- Optional inversion for TX_RST_DLY
   IS_TX_RST_INVERTED => '0',       -- Optional inversion for TX_RST
   RX_DATA_TYPE => "DATA",          -- Defines what the RX input pin is carrying (CLOCK, DATA,
                                    -- DATA_AND_CLOCK, SERIAL)
   RX_DATA_WIDTH => 8,              -- Defines the width of the serial-to-parallel converter (4-8)
   RX_DELAY_FORMAT => "TIME",       -- Units of the RX DELAY_VALUE (COUNT, TIME)
   RX_DELAY_TYPE => "FIXED",        -- Set the type of RX tap delay line (FIXED, VARIABLE, VAR_LOAD)
   RX_DELAY_VALUE => 0,             -- RX Input delay value setting in ps
   RX_REFCLK_FREQUENCY => 300.0,    -- Specification of the RX reference clock frequency in MHz
                                    -- (200.0-2667.0)
   RX_UPDATE_MODE => "ASYNC",       -- Determines when updates to the RX delay will take effect (ASYNC,
                                    -- MANUAL, SYNC)
   SIM_DEVICE => "ULTRASCALE_PLUS", -- Set the device version for simulation functionality (ULTRASCALE,
                                    -- ULTRASCALE_PLUS, ULTRASCALE_PLUS_ES1, ULTRASCALE_PLUS_ES2)
   TBYTE_CTL => "TBYTE_IN",         -- Select between T and TBYTE_IN inputs
   TX_DATA_WIDTH => 8,              -- Parallel data input width (4-8)
   TX_DELAY_FORMAT => "TIME",       -- Units of the TX DELAY_VALUE (COUNT, TIME)
   TX_DELAY_TYPE => "FIXED",        -- Set the type of TX tap delay line (FIXED, VARIABLE, VAR_LOAD)
   TX_DELAY_VALUE => 0,             -- TX Input delay value setting in ps
   TX_OUTPUT_PHASE_90 => "FALSE",   -- Delays the output phase by 90-degrees
   TX_REFCLK_FREQUENCY => 300.0,    -- Specification of the TX reference clock frequency in MHz
                                    -- (200.0-2667.0)
   TX_UPDATE_MODE => "ASYNC"        -- Determines when updates to the delay will take effect (ASYNC, MANUAL,
                                    -- SYNC)
)
port map (
   FIFO_EMPTY => FIFO_EMPTY,           -- 1-bit output: FIFO empty flag
   FIFO_WRCLK_OUT => FIFO_WRCLK_OUT,   -- 1-bit output: FIFO source synchronous write clock out to the
                                       -- device logic (currently unsupported, do not connect)

   O => O,                             -- 1-bit output: Serialized output going to output buffer
   Q => Q,                             -- 8-bit output: Registered output data from FIFO
   RX_BIT_CTRL_OUT => RX_BIT_CTRL_OUT, -- 40-bit output: RX Output bus to BITSLICE_CONTROL
   RX_CNTVALUEOUT => RX_CNTVALUEOUT,   -- 9-bit output: RX Counter value from device logic
   TX_BIT_CTRL_OUT => TX_BIT_CTRL_OUT, -- 40-bit output: Output bus to BITSLICE_CONTROL for TX
   TX_CNTVALUEOUT => TX_CNTVALUEOUT,   -- 9-bit output: TX Counter value to device logic
   T_OUT => T_OUT,                     -- 1-bit output: Byte group 3-state output
   D => D,                             -- 8-bit input: Data from device logic
   DATAIN => DATAIN,                   -- 1-bit input: Input signal from IOBUF
   FIFO_RD_CLK => FIFO_RD_CLK,         -- 1-bit input: FIFO read clock
   FIFO_RD_EN => FIFO_RD_EN,           -- 1-bit input: FIFO read enable
   RX_BIT_CTRL_IN => RX_BIT_CTRL_IN,   -- 40-bit input: RX Input bus from BITSLICE_CONTROL
   RX_CE => RX_CE,                     -- 1-bit input: Clock enable for IDELAY
   RX_CLK => RX_CLK,                   -- 1-bit input: RX Clock used to sample LOAD, CE, INC
   RX_CNTVALUEIN => RX_CNTVALUEIN,     -- 9-bit input: RX Counter value from device logic
   RX_EN_VTC => RX_EN_VTC,             -- 1-bit input: RX Enable to keep stable delay over VT
   RX_INC => RX_INC,                   -- 1-bit input: RX Increment the current delay tap setting
   RX_LOAD => RX_LOAD,                 -- 1-bit input: RX Load the CNTVALUEIN tap setting
   RX_RST => RX_RST,                   -- 1-bit input: RX Asynchronous assert, synchronous deassert for
                                       -- RXTX_BITSLICE ISERDES

   RX_RST_DLY => RX_RST_DLY,           -- 1-bit input: RX Reset the internal DELAY value to DELAY_VALUE
   T => T,                             -- 1-bit input: Legacy T byte input from device logic
   TBYTE_IN => TBYTE_IN,               -- 1-bit input: Byte group 3-state input from TX_BITSLICE_TRI
   TX_BIT_CTRL_IN => TX_BIT_CTRL_IN,   -- 40-bit input: TX Input bus from BITSLICE_CONTROL
   TX_CE => TX_CE,                     -- 1-bit input: Clock enable for ODELAY
   TX_CLK => TX_CLK,                   -- 1-bit input: TX Clock used to sample LOAD, CE, INC
   TX_CNTVALUEIN => TX_CNTVALUEIN,     -- 9-bit input: TX Counter value from device logic
   TX_EN_VTC => TX_EN_VTC,             -- 1-bit input: TX Enable to keep stable delay over VT
   TX_INC => TX_INC,                   -- 1-bit input: TX Increment the current delay tap setting
   TX_LOAD => TX_LOAD,                 -- 1-bit input: TX Load the CNTVALUEIN tap setting
   TX_RST => TX_RST,                   -- 1-bit input: TX Asynchronous assert, synchronous deassert for
                                       -- RXTX_BITSLICE OSERDES

   TX_RST_DLY => TX_RST_DLY            -- 1-bit input: TX Reset the internal DELAY value to DELAY_VALUE
);

-- End of RXTX_BITSLICE_inst instantiation

Verilog Instantiation Template


// RXTX_BITSLICE: RXTX_BITSLICE for bidirectional I/O using Native Mode
//                UltraScale
// Xilinx HDL Language Template, version 2022.1

RXTX_BITSLICE #(
   .ENABLE_PRE_EMPHASIS("FALSE"),  // Enable the pre-emphasis
   .FIFO_SYNC_MODE("FALSE"),       // Always set to FALSE. TRUE is reserved for later use.
   .INIT(1'b1),                    // Defines initial O value
   .IS_RX_CLK_INVERTED(1'b0),      // Optional inversion for RX_CLK
   .IS_RX_RST_DLY_INVERTED(1'b0),  // Optional inversion for RX_RST_DLY
   .IS_RX_RST_INVERTED(1'b0),      // Optional inversion for RX_RST
   .IS_TX_CLK_INVERTED(1'b0),      // Optional inversion for TX_CLK
   .IS_TX_RST_DLY_INVERTED(1'b0),  // Optional inversion for TX_RST_DLY
   .IS_TX_RST_INVERTED(1'b0),      // Optional inversion for TX_RST
   .RX_DATA_TYPE("DATA"),          // Defines what the RX input pin is carrying (CLOCK, DATA,
                                   // DATA_AND_CLOCK, SERIAL)
   .RX_DATA_WIDTH(8),              // Defines the width of the serial-to-parallel converter (4-8)
   .RX_DELAY_FORMAT("TIME"),       // Units of the RX DELAY_VALUE (COUNT, TIME)
   .RX_DELAY_TYPE("FIXED"),        // Set the type of RX tap delay line (FIXED, VARIABLE, VAR_LOAD)
   .RX_DELAY_VALUE(0),             // RX Input delay value setting in ps
   .RX_REFCLK_FREQUENCY(300.0),    // Specification of the RX reference clock frequency in MHz
                                   // (200.0-2667.0)
   .RX_UPDATE_MODE("ASYNC"),       // Determines when updates to the RX delay will take effect (ASYNC,
                                   // MANUAL, SYNC)
   .SIM_DEVICE("ULTRASCALE_PLUS"), // Set the device version for simulation functionality (ULTRASCALE,
                                   // ULTRASCALE_PLUS, ULTRASCALE_PLUS_ES1, ULTRASCALE_PLUS_ES2)
   .TBYTE_CTL("TBYTE_IN"),         // Select between T and TBYTE_IN inputs
   .TX_DATA_WIDTH(8),              // Parallel data input width (4-8)
   .TX_DELAY_FORMAT("TIME"),       // Units of the TX DELAY_VALUE (COUNT, TIME)
   .TX_DELAY_TYPE("FIXED"),        // Set the type of TX tap delay line (FIXED, VARIABLE, VAR_LOAD)
   .TX_DELAY_VALUE(0),             // TX Input delay value setting in ps
   .TX_OUTPUT_PHASE_90("FALSE"),   // Delays the output phase by 90-degrees
   .TX_REFCLK_FREQUENCY(300.0),    // Specification of the TX reference clock frequency in MHz
                                   // (200.0-2667.0)
   .TX_UPDATE_MODE("ASYNC")        // Determines when updates to the delay will take effect (ASYNC, MANUAL,
                                   // SYNC)
)
RXTX_BITSLICE_inst (
   .FIFO_EMPTY(FIFO_EMPTY),           // 1-bit output: FIFO empty flag
   .FIFO_WRCLK_OUT(FIFO_WRCLK_OUT),   // 1-bit output: FIFO source synchronous write clock out to the device
                                      // logic (currently unsupported, do not connect)

   .O(O),                             // 1-bit output: Serialized output going to output buffer
   .Q(Q),                             // 8-bit output: Registered output data from FIFO
   .RX_BIT_CTRL_OUT(RX_BIT_CTRL_OUT), // 40-bit output: RX Output bus to BITSLICE_CONTROL
   .RX_CNTVALUEOUT(RX_CNTVALUEOUT),   // 9-bit output: RX Counter value from device logic
   .TX_BIT_CTRL_OUT(TX_BIT_CTRL_OUT), // 40-bit output: Output bus to BITSLICE_CONTROL for TX
   .TX_CNTVALUEOUT(TX_CNTVALUEOUT),   // 9-bit output: TX Counter value to device logic
   .T_OUT(T_OUT),                     // 1-bit output: Byte group 3-state output
   .D(D),                             // 8-bit input: Data from device logic
   .DATAIN(DATAIN),                   // 1-bit input: Input signal from IOBUF
   .FIFO_RD_CLK(FIFO_RD_CLK),         // 1-bit input: FIFO read clock
   .FIFO_RD_EN(FIFO_RD_EN),           // 1-bit input: FIFO read enable
   .RX_BIT_CTRL_IN(RX_BIT_CTRL_IN),   // 40-bit input: RX Input bus from BITSLICE_CONTROL
   .RX_CE(RX_CE),                     // 1-bit input: Clock enable for IDELAY
   .RX_CLK(RX_CLK),                   // 1-bit input: RX Clock used to sample LOAD, CE, INC
   .RX_CNTVALUEIN(RX_CNTVALUEIN),     // 9-bit input: RX Counter value from device logic
   .RX_EN_VTC(RX_EN_VTC),             // 1-bit input: RX Enable to keep stable delay over VT
   .RX_INC(RX_INC),                   // 1-bit input: RX Increment the current delay tap setting
   .RX_LOAD(RX_LOAD),                 // 1-bit input: RX Load the CNTVALUEIN tap setting
   .RX_RST(RX_RST),                   // 1-bit input: RX Asynchronous assert, synchronous deassert for
                                      // RXTX_BITSLICE ISERDES

   .RX_RST_DLY(RX_RST_DLY),           // 1-bit input: RX Reset the internal DELAY value to DELAY_VALUE
   .T(T),                             // 1-bit input: Legacy T byte input from device logic
   .TBYTE_IN(TBYTE_IN),               // 1-bit input: Byte group 3-state input from TX_BITSLICE_TRI
   .TX_BIT_CTRL_IN(TX_BIT_CTRL_IN),   // 40-bit input: TX Input bus from BITSLICE_CONTROL
   .TX_CE(TX_CE),                     // 1-bit input: Clock enable for ODELAY
   .TX_CLK(TX_CLK),                   // 1-bit input: TX Clock used to sample LOAD, CE, INC
   .TX_CNTVALUEIN(TX_CNTVALUEIN),     // 9-bit input: TX Counter value from device logic
   .TX_EN_VTC(TX_EN_VTC),             // 1-bit input: TX Enable to keep stable delay over VT
   .TX_INC(TX_INC),                   // 1-bit input: TX Increment the current delay tap setting
   .TX_LOAD(TX_LOAD),                 // 1-bit input: TX Load the CNTVALUEIN tap setting
   .TX_RST(TX_RST),                   // 1-bit input: TX Asynchronous assert, synchronous deassert for
                                      // RXTX_BITSLICE OSERDES

   .TX_RST_DLY(TX_RST_DLY)            // 1-bit input: TX Reset the internal DELAY value to DELAY_VALUE
);

// End of RXTX_BITSLICE_inst instantiation

Related Information

See the UltraScale Architecture SelectIO Resources User Guide (UG571).