Absolute Maximum Ratings - DS960

Versal HBM Series Data Sheet: DC and AC Switching Characteristics (DS960)
Document ID
DS960
Release Date
2024-07-24
Revision
1.5 English
Table 1. Absolute Maximum Ratings—Power, Voltages, and Current
Symbol Description 1 Min Max Units
VCCAUX Programmable logic auxiliary power supply –0.500 1.650 V
VCCAUX_PMC Platform management controller (PMC) auxiliary power supply voltage –0.500 1.650 V
VCCAUX_SMON 2 PMC system monitor power supply relative to GND_SMON –0.500 1.650 V
VCC_BATT Battery power supply –0.500 1.650 V
VCC_FUSE eFUSE programming power supply –0.500 2.000 V
VCCINT Programmable logic primary power supply –0.500 0.970 V
VCCINT_GT GTM primary power supply –0.500 0.970 V
VCCINT_IO_HBM 3 High-bandwidth memory controller interface power supply –0.500 0.970 V
VCC_CPM5 CPM5 primary power supply –0.500 0.970 V
VCC_IO 3 XPIO power supply –0.500 0.970 V
VCCO 4

XPIO bank 7## output driver power supply

Where the bank number is the three-digit bank number beginning with 7

 –0.500 1.650 V

PSIO bank 5## power supplies

Where the bank number is the three-digit bank number beginning with 5

 –0.500 3.63 V
VCC_PMC PMC primary power supply –0.500 0.970 V
VCC_PSFP PS full-power domain power supply –0.500 0.970 V
VCC_PSLP PS low-power domain power supply –0.500 0.970 V
VCC_RAM PL RAM and clocking network power supply –0.500 0.970 V
VCC_SOC 3 Network on Chip (NoC) and DDR memory controller power supply –0.500 0.970 V
VIN 4, 5 I/O input voltage for PSIO and XPIO banks –0.550 VCCO + 0.550 V
VREF PMC system monitor reference input (VREFP/VREFN) relative to GND_SMON –0.500 1.120 V
VCCO_HBM I/O supply voltage for the high-bandwidth memory –0.300 1.500 V
VCC_HBM Supply voltage for the high-bandwidth memory –0.300 1.500 V
VCCAUX_HBM Auxiliary supply voltage for the high-bandwidth memory –0.300 3.000 V
GTYP (or GTM) Transceivers

VGTYP_AVCC

VGTM_AVCC

GTYP (or GTM) transceiver primary analog power supply 6

–0.500 0.97 V

VGTYP_AVCCAUX

VGTM_AVCCAUX

GTYP (or GTM) transceiver auxiliary analog (PLL) power supply 6

–0.500 1.650 V

VGTYP_AVTT

VGTM_AVTT

GTYP (or GTM) transceiver termination power supply 6

–0.500 1.320 V

VGTYP_AVTTRCAL

VGTM_AVTTRCAL

GTYP (or GTM) transceiver analog resistor calibration power supply 6

–0.500 1.320 V
VCCINT_GTM Digital supply voltage for select modules in the GTM transceivers –0.500 0.97 V

VGTYP_REFCLK_DC

VGTM_REFCLK_DC

Transceiver reference clock absolute input DC voltage –0.500 1.000 V

VGTYP_REFCLK_AC

VGTM_REFCLK_AC

Transceiver reference clock absolute input AC voltage 7 –0.500 1.350 V
VIN_DC Receiver (RXP/RXN) and transmitter (TXP/TXN) absolute DC voltage Unpowered –0.800 0.800 V
Powered –0.300 1.000 V
VIN_AC+DC Receiver (RXP/RXN) and transmitter (TXP/TXN) absolute AC plus DC voltage Unpowered –0.800 0.800 V
Powered –0.500 1.250 V
IDCIN_FLOAT DC input current for receiver input pins DC coupled RX termination = floating 8 – 10 mA

IDCIN_GTYP_AVTT

DC input current for GTYP receiver input pins DC coupled RX termination =  or VGTYP_AVTT – 16 mA
IDCIN_GTM_AVTT DC input current for GTM receiver input pins DC coupled RX termination = VGTM_AVTT – 16 mA

IDCIN_GTYP_GND

DC input current for GTYP receiver input pins DC coupled RX termination = GND 10 – 16 mA
IDCIN_GTM_GND DC input current for GTM receiver input pins DC coupled RX termination = GND – 16 mA
IDCIN_PROG DC input current for receiver input pins DC coupled RX termination = programmable 9 – 0 mA
IDCOUT_FLOAT DC output current for transmitter pins DC coupled RX termination = floating – 6 mA

IDCOUT_GTYP_AVTT

DC output current for transmitter pins DC coupled RX termination =  or VGTYP_AVTT – 6 mA
Other Ratings
IDC Available output current at the pad –20 20 mA
IRMS Available RMS output current at the pad –20 20 mA
  1. Stresses beyond those listed under Absolute Maximum Ratings might cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those listed under Operating Conditions is not implied. Exposure to Absolute Maximum Ratings conditions for extended periods of time might affect device reliability.
  2. VCCAUX_SMON must be connected to VCCAUX_PMC . See Versal Adaptive SoC System Monitor Architecture Manual (AM006) for VCCAUX_SMON information and filter considerations.
  3. VCCINT_IO_HBM and VCC_IO must be connected to VCC_SOC.
  4. When operating outside of the recommended operating conditions, refer to the specifications in the VIN Maximum Allowed AC Voltage Overshoot and Undershoot section.
  5. The lower absolute voltage specification always applies.
  6. For more information on supported GTYP (or GTM) transceiver terminations see the Versal Adaptive SoC GTY and GTYP Transceivers Architecture Manual (AM002) or Versal Adaptive SoC GTM Transceivers Architecture Manual (AM017) .
  7. The or GTYP_REFCLK AC signal operates in the reference clock frequency range. See GTYP Transceiver Reference Clock Switching Characteristics.
  8. AC coupled operation is not supported for RX termination = floating.
  9. DC coupled operation is not supported for RX termination = programmable.
  10. For DC coupled links with RX termination set to ground, the transmitter or the board should insure that the RX input common mode voltage is set between 0.2V and 0.8V.
Table 2. Absolute Maximum Ratings—Temperature
Symbol Description 1 Min Max Units
TSTG Storage temperature (ambient, unpowered) –55 120 °C
TSOL 2 Maximum dry rework soldering temperature – 260 °C
Tj Maximum junction temperature – 120 °C
  1. Stresses beyond those listed under Absolute Maximum Ratings might cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those listed under Operating Conditions is not implied. Exposure to Absolute Maximum Ratings conditions for extended periods of time might affect device reliability.
  2. For soldering guidelines and thermal considerations, see the Versal Adaptive SoC Packaging and Pinouts Architecture Manual (AM013).