The device configuration settings for the AMD Artix™
UltraScale+™
, AMD Virtex™
UltraScale+™
, and AMD Kintex™
UltraScale+™
™ devices available for
use with the set_property <Setting> <Value>
[current_design]
Vivado tool Tcl command are shown in the following
table.
| Setting | Default Value | Possible Values | Description |
|---|---|---|---|
| BITSTREAM.CONFIG.QSPI_STACKED | DISABLE | DISABLE, ENABLE | Enable post-configuration access to the QSPI when in Dual Stacked QSPI (SPIx4) mode. |
| BITSTREAM.CONFIG.MULTIBOOT_DEBUG | DISABLE | ENABLE, DISABLE | Only used for debugging boot issues. Setting to ENABLE disables fallback to collect additional debug information. |
| BITSTREAM.CONFIG.SECONDARY_BOOT | NONE | NONE, AXI32, MCAP, JTAG | Select the source for secondary boot. |
| BITSTREAM.CONFIG.OSPI_DDR | DISABLE | DISABLE, ENABLE | Enables the DDR feature in Master OSPI configuration mode. |
| BITSTREAM.CONFIG.CONFIGRATE | 21 | 127, 102, 85, 72, 63, 56, 51, 42, 31, 25, 21 | Select the frequency in MHz for the internally generated configuration clock source (CCLK). |
| BITSTREAM.ENCRYPTION.RED_KEY_CLEAR | DISABLE | DISABLE, ENABLE | Enable Red Key Clear after configuration |
| BITSTREAM.POWER.PMC_CLK_FREQ | 255 | 255, 170, 127, 102, 85, 72, 63, 56, 51, 46, 42, 39, 36, 34 | Set the PMC Clock Frequency after configuration completes |
| BITSTREAM.POWER.CCU_CLK_FREQ | 127 | 170, 127, 102, 85, 72, 63, 56, 51, 46, 42, 39, 36, 34 | Set the CCU Clock Frequency after configuration completes |
| BITSTREAM.GENERAL.SYSMON_JTAG_DRP | ENABLE | ENABLE, DISABLE | Enable SYSMON DRP Instruction in JTAG TAP |
| BITSTREAM.READBACK.ENABLE | ENABLE | ENABLE, DISABLE | Enable READBACK |
| BITSTREAM.CONFIG.OSPI_ECC_FAIL | DISABLE | DISABLE, ENABLE | Enable OSPI ECC Fail |
| BITSTREAM.EAM.DFX_UNEXPECTED_ACTIV_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a DFX Unexpected Activ Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.JTAG_TOGGLE_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a JTAG Toggle Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.EFUSE_CACHE_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a eFUSE Cache Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.ROM_VALID_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a ROM Valid Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.PMC_FW_NCR_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a PMC Firmware Non-Correctible Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.PMC_FW_CR_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a PMC Firmware Correctible Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.PMC_BOOT_NCR_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a PMC Boot Non-Correctible Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.SBI_SMAP_OVF_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a SelectMAP Overflow Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.SSS_CFG_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a Slave Serial Config Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.EFUSE_RD_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a eFUSE Read Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.EFUSE_PGM_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a eFUSE Programming Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.OSPI_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a OSPI Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.SBI_JTAG_OVF_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a JTAG Overflow Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.SBI_SS_OVF_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a Slave Serial Overflow Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.SBI_MCAP_OVF_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a MCAP Overflow Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.SBI_SMAP_CONFIG_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a SelectMAP Configuration Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.SBI_AXI_APB_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a AXI APB Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.SBI_SMAP_ABORT | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a SelectMAP Abort Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.CCU_TAMPER_FABRIC | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a Tamper Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.SYSMON_OT | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a Sysmon Over Temperature Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.CCU_BAD_PR_FORMAT | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a Bad Packet Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.CCU_SEU_ECC_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a CCU_SEU_ECC_ERR. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.CCU_SEU_CRC_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a CCU_SEU_CRC_ERR. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.CCU_CRC_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a CCU_CRC_ERR. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.CCU_IDCODE_ERR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a IDCODE Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.CCU_APB_ERROR | NONE | NONE, ERROR_OUT, SLD, SRST | Set the Error Aggregator Module (EAM) response for a APB Error. ERROR_OUT selects the EAM response to drive the INIT_B pin low if this error is detected. SLD selects the EAM response to send the system into secure lock-down state. SRST selects the EAM response to issue a system reset. |
| BITSTREAM.EAM.SECLKDWN_IO_TRISTATE | DISABLE | DISABLE, ENABLE | Enable IO Tri-State if system enters secure lockdown. |