XPLL - 2024.1 English

Versal Architecture Premium Series Libraries Guide (UG1485)

Document ID
UG1485
Release Date
2024-05-30
Version
2024.1 English

Primitive: XPIO PLL

  • PRIMITIVE_GROUP: CLOCK
  • PRIMITIVE_SUBGROUP: PLL
Page-1 Sheet.2 XPLL XPLL Text Line.6 CLKFB1_DESKEW CLKFB1_DESKEW Text Line.7 CLKFB2_DESKEW CLKFB2_DESKEW Text Line.8 CLKIN CLKIN Text Line.9 CLKIN1_DESKEW CLKIN1_DESKEW Text Line.25 CLKIN2_DESKEW CLKIN2_DESKEW Text Line.27 CLKOUTPHYEN CLKOUTPHYEN Text Line.29 DADDR[6:0] DADDR[6:0] Text Line.30 DI[15:0] DI[15:0] Text Line.33 PSINCDEC PSINCDEC Text Line.36 DEN DEN Text Line.37 RIU_WR_DATA[15:0] RIU_WR_DATA[15:0] Text Line.167 DWE DWE Text Line.170 PSCLK PSCLK Text Line.171 PSEN PSEN Text Line.174 PWRDWN PWRDWN Text Line.175 RIU_ADDR[7:0] RIU_ADDR[7:0] Text Line.176 RIU_CLK RIU_CLK Text Line.178 RIU_NIBBLE_SEL RIU_NIBBLE_SEL Text Line.181 RIU_WR_EN RIU_WR_EN Text Line.182 RST RST Text Line.50 DCLK DCLK Text Line.98 CLKOUTPHY CLKOUTPHY Text Line.99 CLKOUT0 CLKOUT0 Text Line.100 CLKOUT1 CLKOUT1 Text Line.101 CLKOUT2 CLKOUT2 Text Line.106 DO[15:0] DO[15:0] Text Line.107 DRDY DRDY Text Line.34 LOCKED LOCKED Text Line.35 LOCKED_FB LOCKED_FB Sheet.36 LOCKED1_DESKEW LOCKED1_DESKEW Sheet.37 LOCKED2_DESKEW LOCKED2_DESKEW Sheet.38 PSDONE PSDONE Sheet.39 RIU_RD_DATA[15:0] RIU_RD_DATA[15:0] Sheet.40 RIU_VALID RIU_VALID Text Line.43 CLKOUT3 CLKOUT3 Sheet.44 X22737-042219 X22737-042219

Introduction

The XPLL is a mixed signal block design to support frequency synthesis, clock network deskew, and jitter reduction. The clock outputs can each have an individual divide, phase shift, and duty cycle based on the same VCO frequency. The primary function of the XPLL is to support the clocking needs of Memory Interface IP and XPHY Logic.

Port Descriptions

Port Direction Width Function
CLKFB1_DESKEW Input 1 Secondary (feedback) clock input to the PD1 block for deskewing clock network delays.
CLKFB2_DESKEW Input 1 Secondary (feedback) clock input to the PD2 block for deskewing clock network delays.
CLKIN Input 1 Primary clock input
CLKIN1_DESKEW Input 1 Primary clock input to the PD1 block for deskewing clock network delays between two different CLKOUT networks.
CLKIN2_DESKEW Input 1 Primary clock input to the PD2 block for deskewing clock network delays between two different CLKOUT networks.
CLKOUTPHY Output 1 General clock output connected to XPHY Logic.
CLKOUTPHY_CASC_IN Input 1 XPLL CLKOUTPHY cascade input
CLKOUTPHY_CASC_OUT Output 1 XPLL CLKOUTPHY cascade output
CLKOUTPHYEN Input 1 Enable signal for CLKOUTPHY.
CLKOUT0 Output 1 CLKOUT0 output.
CLKOUT1 Output 1 CLKOUT1 output.
CLKOUT2 Output 1 CLKOUT2 output.
CLKOUT3 Output 1 CLKOUT3 output.
DADDR<6:0> Input 7 The dynamic reconfiguration address (DADDR) input bus provides a reconfiguration address for the dynamic reconfiguration. When not used, all bits must be assigned zeros.
DCLK Input 1 The DCLK signal is the reference clock for the dynamic reconfiguration port
DEN Input 1 The dynamic reconfiguration enable (DEN) provides the enable control signal to access the dynamic reconfiguration feature. When the dynamic reconfiguration feature is not used, DEN must be tied Low.
DI<15:0> Input 16 The dynamic reconfiguration data input (DI) bus provides reconfiguration data. When not used, all bits must be set to zero.
DO<15:0> Output 16 The dynamic reconfiguration output bus provides XPLL data output when using dynamic reconfiguration.
DRDY Output 1 The dynamic reconfiguration ready output (DRDY) provides the response to the DEN signal for the XPLLs dynamic reconfiguration feature.
DWE Input 1 The dynamic reconfiguration write enable (DWE) input pin provides the write enable control signal to write the DI data into the DADDR address. When not used, it must be tied Low.
LOCKED Output 1 The LOCKED signal indicates that all functions requiring a LOCKED signal for the XPLL to operate properly have LOCKED. This LOCKED signal is therefore an AND function of LOCKED_FB, LOCKED1_DESKEW, and LOCKED2_DESKEW if used.
LOCKED_FB Output 1 An output from the XPLL that indicates when the XPLL has achieved phase alignment within a predefined window and frequency matching within a predefined PPM range. The XPLL automatically locks after power on. No extra reset is required. LOCKED is deasserted if the input clock stops or the phase alignment is violated (for example, input clock phase shift). The XPLL must be reset after LOCKED is deasserted.
LOCKED1_DESKEW Output 1 Indicates if the PD1 circuit is locked. Applies only to the deskew circuits used in the design. Ignore these outputs for unused deskew circuits.
LOCKED2_DESKEW Output 1 Indicates if the PD2 circuit is locked. Applies only to the deskew circuits used in the design. Ignore these outputs for unused deskew circuits.
PSCLK Input 1 Phase shift clock.
PSDONE Output 1 Phase shift done.
PSEN Input 1 Phase shift enable.
PSINCDEC Input 1 Phase shift increment/decrement.
PWRDWN Input 1 Powers down instantiated but unused XPLLs.
RIU_ADDR<7:0> Input 8 Dedicated connection to the DDRMC_RIU Register Interface Unit Address.
RIU_CLK Input 1 Dedicated connection to the DDRMC_RIU Register Interface Unit Clock.
RIU_NIBBLE_SEL Input 1 Dedicated connection to the DDRMC_RIU Register Interface Unit Nibble Select.
RIU_RD_DATA<15:0> Output 16 Dedicated connection to the DDRMC_RIU Register Interface Unit Read Data.
RIU_VALID Output 1 Dedicated connection to the DDRMC_RIU Register Interface Unit Interface Valid.
RIU_WR_DATA<15:0> Input 16 Dedicated connection to the DDRMC_RIU Register Interface Unit Write Data.
RIU_WR_EN Input 1 Dedicated connection to the DDRMC_RIU register Interface Unit Write Enable.
RST Input 1 Asynchronous reset signal. The RST signal is an asynchronous reset for the XPLL. The XPLL synchronously re-enables itself when this signal is released (that is, XPLL re-enabled). A reset is required when the input clock conditions change (for example, frequency).

Design Entry Method

Instantiation Yes
Inference No
IP and IP Integrator Catalog Recommended

Available Attributes

Attribute Type Allowed Values Default Description
CLKFBOUT_MULT DECIMAL 4 to 43 42 Specifies the amount to multiply all CLKOUT clock outputs if a different frequency is desired. This number, in combination with the associated CLKOUT#_DIVIDE value and DIVCLK_DIVIDE value, will determine the output frequency.
CLKFBOUT_PHASE 3 significant digit FLOAT -360.000 to 360.000 0.000 Specifies the phase offset in degrees of the clock feedback output. Shifting the feedback clock results in a negative phase shift of all output clocks to the XPLL.
CLKIN_PERIOD FLOAT(nS) 0.000 to 100.000 0.000 Specifies the input period to the CLKIN1 in ns.
CLKOUTPHY_CASCIN_EN BINARY 1'b0 to 1'b1 1'b0 XPLL CLKOUTPHY cascade input enable
CLKOUTPHY_CASCOUT_EN BINARY 1'b0 to 1'b1 1'b0 XPLL CLKOUTPHY cascade output enable
CLKOUT0_DIVIDE DECIMAL 2 to 128 2 Specifies the amount to divide the CLKOUT0 output. This number in combination with the CLKFBOUT_MULT and DIVCLK_DIVIDE values will determine the output frequency.
CLKOUT0_DUTY_CYCLE 3 significant digit FLOAT 0.001 to 0.999 0.500 Specifies the Duty Cycle of CLKOUT0 clock output in percentage (i.e., 0.500 will generate a 50% duty cycle).
CLKOUT0_PHASE 3 significant digit FLOAT -360.000 to 360.000 0.000 Specifies the phase offset in degrees of the CLKOUT0 output. In static phase shift mode, the minimum phase step resolution (degrees) = (360 / CLKOUT0_DIVIDE) / 8
CLKOUT0_PHASE_CTRL BINARY 2'b00 to 2'b11 2'b00 CLKOUT0 counter variable fine phase shift or deskew select.
  • 00: Interpolator is not controlled by either deskew or phase shift interface.
  • 01: Interpolator is controlled by Deskew.
  • 10: Interpolator is controlled by phase shift interface.
  • 11: Interpolator is controlled by PD2.
CLKOUT1_DIVIDE DECIMAL 2 to 128 2 Specifies the amount to divide the CLKOUT1 output. This number in combination with the CLKFBOUT_MULT and DIVCLK_DIVIDE values will determine the output frequency.
CLKOUT1_DUTY_CYCLE 3 significant digit FLOAT 0.001 to 0.999 0.500 Specifies the Duty Cycle of CLKOUT1 clock output in percentage (i.e., 0.500 will generate a 50% duty cycle).
CLKOUT1_PHASE 3 significant digit FLOAT -360.000 to 360.000 0.000 Specifies the phase offset in degrees of the CLKOUT1 output. In static phase shift mode, the minimum phase step resolution (degrees) = (360 / CLKOUT1_DIVIDE) / 8
CLKOUT1_PHASE_CTRL BINARY 2'b00 to 2'b11 2'b00 CLKOUT0 counter variable fine phase shift or deskew select.
  • 00: Interpolator is not controlled by either deskew or phase shift interface.
  • 01: Interpolator is controlled by Deskew.
  • 10: Interpolator is controlled by phase shift interface.
  • 11: Interpolator is controlled by PD2.
CLKOUT2_DIVIDE DECIMAL 2 to 128 2 Specifies the amount to divide the CLKOUT2 output. This number in combination with the CLKFBOUT_MULT and DIVCLK_DIVIDE values will determine the output frequency.
CLKOUT2_DUTY_CYCLE 3 significant digit FLOAT 0.001 to 0.999 0.500 Specifies the Duty Cycle of CLKOUT2 clock output in percentage (i.e., 0.500 will generate a 50% duty cycle).
CLKOUT2_PHASE 3 significant digit FLOAT -360.000 to 360.000 0.000 Specifies the phase offset in degrees of the CLKOUT2 output. In static phase shift mode, the minimum phase step resolution (degrees) = (360 / CLKOUT2_DIVIDE) / 8
CLKOUT2_PHASE_CTRL BINARY 2'b00 to 2'b11 2'b00 CLKOUT2 counter variable fine phase shift or deskew select.
  • 00: Interpolator is not controlled by either deskew or phase shift interface.
  • 01: Interpolator is controlled by Deskew.
  • 10: Interpolator is controlled by phase shift interface.
  • 11: Interpolator is controlled by PD2.
CLKOUT3_DIVIDE DECIMAL 2 to 128 2 Specifies the amount to divide the CLKOUT3 output. This number in combination with the CLKFBOUT_MULT and DIVCLK_DIVIDE values will determine the output frequency.
CLKOUT3_DUTY_CYCLE 3 significant digit FLOAT 0.001 to 0.999 0.500 Specifies the Duty Cycle of CLKOUT3 clock output in percentage (i.e., 0.500 will generate a 50% duty cycle).
CLKOUT3_PHASE 3 significant digit FLOAT -360.000 to 360.000 0.000 Specifies the phase offset in degrees of the CLKOUT3 output. In static phase shift mode, the minimum phase step resolution (degrees) = (360 / CLKOUT3_DIVIDE) / 8
CLKOUT3_PHASE_CTRL BINARY 2'b00 to 2'b11 2'b00 CLKOUT3 counter variable fine phase shift or deskew select.
  • 00: Interpolator is not controlled by either deskew or phase shift interface.
  • 01: Interpolator is controlled by Deskew.
  • 10: Interpolator is controlled by phase shift interface.
  • 11: Interpolator is controlled by PD2.
DESKEW_DELAY_EN1 STRING "FALSE", "TRUE" "FALSE" Set to TRUE to enable the optional programmable delay in the PD1 circuit.
DESKEW_DELAY_EN2 STRING "FALSE", "TRUE" "FALSE" Set to TRUE to enable the optional programmable delay in the PD2 circuit.
DESKEW_DELAY_PATH1 STRING "FALSE", "TRUE" "FALSE" Determines if the CLKIN1_DESKEW path or the CLKFB1_DESKEW path is selected for the optional programmable delay. TRUE = CLKFB1_DESKEW, FALSE = CLKIN1_DESKEW.
DESKEW_DELAY_PATH2 STRING "FALSE", "TRUE" "FALSE" Determines if the CLKIN2_DESKEW path or the CLKFB2_DESKEW path is selected for the optional programmable delay. TRUE = CLKFB2_DESKEW, FALSE = CLKIN2_DESKEW.
DESKEW_DELAY1 DECIMAL 0 to 63 0 Value of the optional programmable delay in the PD1 circuit.
DESKEW_DELAY2 DECIMAL 0 to 63 0 Value of the optional programmable delay in the PD2 circuit.
DESKEW_MUXIN_SEL BINARY 1'b0 to 1'b1 1'b0 Deskew mux selection
DESKEW2_MUXIN_SEL BINARY 1'b0 to 1'b1 1'b0 Deskew mux selection
DIVCLK_DIVIDE DECIMAL 1 to 12 1 Specifies the division ratio for all output clocks with respect to the input clock. Effectively divides the CLKIN going into the PFD.
IS_CLKFB1_DESKEW_INVERTED BINARY 1'b0 to 1'b1 1'b0 Specifies whether or not to use the optional inversion on the CLKFB1_DESKEW pin.
IS_CLKFB2_DESKEW_INVERTED BINARY 1'b0 to 1'b1 1'b0 Specifies whether or not to use the optional inversion on the CLKFB2_DESKEW pin.
IS_CLKIN_INVERTED BINARY 1'b0 to 1'b1 1'b0 Specifies whether or not to use the optional inversion on the CLKIN pin.
IS_CLKIN1_DESKEW_INVERTED BINARY 1'b0 to 1'b1 1'b0 Specifies whether or not to use the optional inversion on the CLKIN1_DESKEW pin.
IS_CLKIN2_DESKEW_INVERTED BINARY 1'b0 to 1'b1 1'b0 Specifies whether or not to use the optional inversion on the CLKIN2_DESKEW pin.
IS_PSEN_INVERTED BINARY 1'b0 to 1'b1 1'b0 Specifies whether or not to use the optional inversion on the PSEN pin.
IS_PSINCDEC_INVERTED BINARY 1'b0 to 1'b1 1'b0 Specifies whether or not to use the optional inversion on the PSINCDEC pin.
IS_PWRDWN_INVERTED BINARY 1'b0 to 1'b1 1'b0 Specifies whether or not to use the optional inversion on the PWRDWN pin.
IS_RST_INVERTED BINARY 1'b0 to 1'b1 1'b0 Specifies whether or not to use the optional inversion on the RST pin.
LOCK_WAIT STRING "FALSE", "TRUE" "FALSE" Wait during the configuration for the startup for the XPLL to lock.
REF_JITTER 3 significant digit FLOAT 0.000 to 0.200 0.010 Allows specification of the expected jitter on CLKIN to better optimize PLL performance. A bandwidth setting of OPTIMIZED will attempt to choose the best parameter for input clocking when unknown. If known, then the value provided should be specified in terms of the unit interval (UI) (the maximum peak to peak value) of the expected jitter on the input clock.
SIM_ADJ_CLK0_CASCADE STRING "FALSE", "TRUE" "FALSE" Simulation only attribute to reduce CLKOUT0 skew due to missing route delay. Setting the value to TRUE reduce the CLKOUT0 skew in the XPLL cascade.
XPLL_CONNECT_TO_NOCMC STRING "NONE", "DDR", "LP4" "NONE" Indicates if the XPLL is used to drive the DDRMC.

VHDL Instantiation Template

Unless they already exist, copy the following two statements and paste them before the entity declaration.
Library UNISIM;
use UNISIM.vcomponents.all;

-- XPLL: XPIO PLL
--       Versal Premium series
-- Xilinx HDL Language Template, version 2024.1

XPLL_inst : XPLL
generic map (
   CLKFBOUT_MULT => 42,              -- Multiply value for all CLKOUT, (4-43)
   CLKFBOUT_PHASE => 0.0,            -- Phase offset in degrees of CLKFB
   CLKIN_PERIOD => 0.0,              -- Input clock period in ns to ps resolution (i.e. 33.333 is 30 MHz).
   CLKOUT0_DIVIDE => 2,              -- Divide amount for CLKOUT0 (2-128)
   CLKOUT0_DUTY_CYCLE => 0.5,        -- Duty cycle for CLKOUT0
   CLKOUT0_PHASE => 0.0,             -- Phase offset for CLKOUT0
   CLKOUT0_PHASE_CTRL => "00",       -- CLKOUT0 fine phase shift or deskew select (0-11)
   CLKOUT1_DIVIDE => 2,              -- Divide amount for CLKOUT1 (2-128)
   CLKOUT1_DUTY_CYCLE => 0.5,        -- Duty cycle for CLKOUT1
   CLKOUT1_PHASE => 0.0,             -- Phase offset for CLKOUT1
   CLKOUT1_PHASE_CTRL => "00",       -- CLKOUT1 fine phase shift or deskew select (0-11)
   CLKOUT2_DIVIDE => 2,              -- Divide amount for CLKOUT2 (2-128)
   CLKOUT2_DUTY_CYCLE => 0.5,        -- Duty cycle for CLKOUT2
   CLKOUT2_PHASE => 0.0,             -- Phase offset for CLKOUT2
   CLKOUT2_PHASE_CTRL => "00",       -- CLKOUT2 fine phase shift or deskew select (0-11)
   CLKOUT3_DIVIDE => 2,              -- Divide amount for CLKOUT3 (2-128)
   CLKOUT3_DUTY_CYCLE => 0.5,        -- Duty cycle for CLKOUT3
   CLKOUT3_PHASE => 0.0,             -- Phase offset for CLKOUT3
   CLKOUT3_PHASE_CTRL => "00",       -- CLKOUT3 fine phase shift or deskew select (0-11)
   CLKOUTPHY_CASCIN_EN => '0',       -- XPLL CLKOUTPHY cascade input enable
   CLKOUTPHY_CASCOUT_EN => '0',      -- XPLL CLKOUTPHY cascade output enable
   DESKEW2_MUXIN_SEL => '0',         -- Deskew mux selection
   DESKEW_DELAY1 => 0,               -- Deskew optional programmable delay
   DESKEW_DELAY2 => 0,               -- Deskew optional programmable delay
   DESKEW_DELAY_EN1 => "FALSE",      -- Enable deskew optional programmable delay
   DESKEW_DELAY_EN2 => "FALSE",      -- Enable deskew optional programmable delay
   DESKEW_DELAY_PATH1 => "FALSE",    -- Select CLKIN1_DESKEW (TRUE) or CLKFB1_DESKEW (FALSE)
   DESKEW_DELAY_PATH2 => "FALSE",    -- Select CLKIN2_DESKEW (TRUE) or CLKFB2_DESKEW (FALSE)
   DESKEW_MUXIN_SEL => '0',          -- Deskew mux selection
   DIVCLK_DIVIDE => 1,               -- Master division value
   IS_CLKFB1_DESKEW_INVERTED => '0', -- Optional inversion for CLKFB1_DESKEW
   IS_CLKFB2_DESKEW_INVERTED => '0', -- Optional inversion for CLKFB2_DESKEW
   IS_CLKIN1_DESKEW_INVERTED => '0', -- Optional inversion for CLKIN1_DESKEW
   IS_CLKIN2_DESKEW_INVERTED => '0', -- Optional inversion for CLKIN2_DESKEW
   IS_CLKIN_INVERTED => '0',         -- Optional inversion for CLKIN
   IS_PSEN_INVERTED => '0',          -- Optional inversion for PSEN
   IS_PSINCDEC_INVERTED => '0',      -- Optional inversion for PSINCDEC
   IS_PWRDWN_INVERTED => '0',        -- Optional inversion for PWRDWN
   IS_RST_INVERTED => '0',           -- Optional inversion for RST
   LOCK_WAIT => "FALSE",             -- Lock wait
   REF_JITTER => 0.0,                -- Reference input jitter in UI (0.000-0.200).
   SIM_ADJ_CLK0_CASCADE => "FALSE",  -- Simulation only attribute to reduce CLKOUT0 skew when cascading
                                     -- (FALSE, TRUE)
   XPLL_CONNECT_TO_NOCMC => "NONE"   -- XPLL driving the DDRMC
)
port map (
   CLKOUT0 => CLKOUT0,                       -- 1-bit output: CLKOUT0
   CLKOUT1 => CLKOUT1,                       -- 1-bit output: CLKOUT1
   CLKOUT2 => CLKOUT2,                       -- 1-bit output: CLKOUT2
   CLKOUT3 => CLKOUT3,                       -- 1-bit output: CLKOUT3
   CLKOUTPHY => CLKOUTPHY,                   -- 1-bit output: XPHY Logic clock
   CLKOUTPHY_CASC_OUT => CLKOUTPHY_CASC_OUT, -- 1-bit output: XPLL CLKOUTPHY cascade output
   DO => DO,                                 -- 16-bit output: DRP data output
   DRDY => DRDY,                             -- 1-bit output: DRP ready
   LOCKED => LOCKED,                         -- 1-bit output: LOCK
   LOCKED1_DESKEW => LOCKED1_DESKEW,         -- 1-bit output: LOCK DESKEW PD1
   LOCKED2_DESKEW => LOCKED2_DESKEW,         -- 1-bit output: LOCK DESKEW PD2
   LOCKED_FB => LOCKED_FB,                   -- 1-bit output: LOCK FEEDBACK
   PSDONE => PSDONE,                         -- 1-bit output: Phase shift done
   CLKFB1_DESKEW => CLKFB1_DESKEW,           -- 1-bit input: Secondary clock input to PD1
   CLKFB2_DESKEW => CLKFB2_DESKEW,           -- 1-bit input: Secondary clock input to PD2
   CLKIN => CLKIN,                           -- 1-bit input: Primary clock
   CLKIN1_DESKEW => CLKIN1_DESKEW,           -- 1-bit input: Primary clock input to PD1
   CLKIN2_DESKEW => CLKIN2_DESKEW,           -- 1-bit input: Primary clock input to PD2
   CLKOUTPHYEN => CLKOUTPHYEN,               -- 1-bit input: CLKOUTPHY enable
   CLKOUTPHY_CASC_IN => CLKOUTPHY_CASC_IN,   -- 1-bit input: XPLL CLKOUTPHY cascade input
   DADDR => DADDR,                           -- 7-bit input: DRP address
   DCLK => DCLK,                             -- 1-bit input: DRP clock
   DEN => DEN,                               -- 1-bit input: DRP enable
   DI => DI,                                 -- 16-bit input: DRP data input
   DWE => DWE,                               -- 1-bit input: DRP write enable
   PSCLK => PSCLK,                           -- 1-bit input: Phase shift clock
   PSEN => PSEN,                             -- 1-bit input: Phase shift enable
   PSINCDEC => PSINCDEC,                     -- 1-bit input: Phase shift increment/decrement
   PWRDWN => PWRDWN,                         -- 1-bit input: Power-down
   RST => RST                                -- 1-bit input: Reset
);

-- End of XPLL_inst instantiation

Verilog Instantiation Template


// XPLL: XPIO PLL
//       Versal Premium series
// Xilinx HDL Language Template, version 2024.1

XPLL #(
   .CLKFBOUT_MULT(42),               // Multiply value for all CLKOUT, (4-43)
   .CLKFBOUT_PHASE(0.0),             // Phase offset in degrees of CLKFB
   .CLKIN_PERIOD(0.0),               // Input clock period in ns to ps resolution (i.e. 33.333 is 30 MHz).
   .CLKOUT0_DIVIDE(2),               // Divide amount for CLKOUT0 (2-128)
   .CLKOUT0_DUTY_CYCLE(0.5),         // Duty cycle for CLKOUT0
   .CLKOUT0_PHASE(0.0),              // Phase offset for CLKOUT0
   .CLKOUT0_PHASE_CTRL(2'b00),       // CLKOUT0 fine phase shift or deskew select (0-11)
   .CLKOUT1_DIVIDE(2),               // Divide amount for CLKOUT1 (2-128)
   .CLKOUT1_DUTY_CYCLE(0.5),         // Duty cycle for CLKOUT1
   .CLKOUT1_PHASE(0.0),              // Phase offset for CLKOUT1
   .CLKOUT1_PHASE_CTRL(2'b00),       // CLKOUT1 fine phase shift or deskew select (0-11)
   .CLKOUT2_DIVIDE(2),               // Divide amount for CLKOUT2 (2-128)
   .CLKOUT2_DUTY_CYCLE(0.5),         // Duty cycle for CLKOUT2
   .CLKOUT2_PHASE(0.0),              // Phase offset for CLKOUT2
   .CLKOUT2_PHASE_CTRL(2'b00),       // CLKOUT2 fine phase shift or deskew select (0-11)
   .CLKOUT3_DIVIDE(2),               // Divide amount for CLKOUT3 (2-128)
   .CLKOUT3_DUTY_CYCLE(0.5),         // Duty cycle for CLKOUT3
   .CLKOUT3_PHASE(0.0),              // Phase offset for CLKOUT3
   .CLKOUT3_PHASE_CTRL(2'b00),       // CLKOUT3 fine phase shift or deskew select (0-11)
   .CLKOUTPHY_CASCIN_EN(1'b0),       // XPLL CLKOUTPHY cascade input enable
   .CLKOUTPHY_CASCOUT_EN(1'b0),      // XPLL CLKOUTPHY cascade output enable
   .DESKEW2_MUXIN_SEL(1'b0),         // Deskew mux selection
   .DESKEW_DELAY1(0),                // Deskew optional programmable delay
   .DESKEW_DELAY2(0),                // Deskew optional programmable delay
   .DESKEW_DELAY_EN1("FALSE"),       // Enable deskew optional programmable delay
   .DESKEW_DELAY_EN2("FALSE"),       // Enable deskew optional programmable delay
   .DESKEW_DELAY_PATH1("FALSE"),     // Select CLKIN1_DESKEW (TRUE) or CLKFB1_DESKEW (FALSE)
   .DESKEW_DELAY_PATH2("FALSE"),     // Select CLKIN2_DESKEW (TRUE) or CLKFB2_DESKEW (FALSE)
   .DESKEW_MUXIN_SEL(1'b0),          // Deskew mux selection
   .DIVCLK_DIVIDE(1),                // Master division value
   .IS_CLKFB1_DESKEW_INVERTED(1'b0), // Optional inversion for CLKFB1_DESKEW
   .IS_CLKFB2_DESKEW_INVERTED(1'b0), // Optional inversion for CLKFB2_DESKEW
   .IS_CLKIN1_DESKEW_INVERTED(1'b0), // Optional inversion for CLKIN1_DESKEW
   .IS_CLKIN2_DESKEW_INVERTED(1'b0), // Optional inversion for CLKIN2_DESKEW
   .IS_CLKIN_INVERTED(1'b0),         // Optional inversion for CLKIN
   .IS_PSEN_INVERTED(1'b0),          // Optional inversion for PSEN
   .IS_PSINCDEC_INVERTED(1'b0),      // Optional inversion for PSINCDEC
   .IS_PWRDWN_INVERTED(1'b0),        // Optional inversion for PWRDWN
   .IS_RST_INVERTED(1'b0),           // Optional inversion for RST
   .LOCK_WAIT("FALSE"),              // Lock wait
   .REF_JITTER(0.0),                 // Reference input jitter in UI (0.000-0.200).
   .SIM_ADJ_CLK0_CASCADE("FALSE"),   // Simulation only attribute to reduce CLKOUT0 skew when cascading
                                     // (FALSE, TRUE)
   .XPLL_CONNECT_TO_NOCMC("NONE")    // XPLL driving the DDRMC
)
XPLL_inst (
   .CLKOUT0(CLKOUT0),                       // 1-bit output: CLKOUT0
   .CLKOUT1(CLKOUT1),                       // 1-bit output: CLKOUT1
   .CLKOUT2(CLKOUT2),                       // 1-bit output: CLKOUT2
   .CLKOUT3(CLKOUT3),                       // 1-bit output: CLKOUT3
   .CLKOUTPHY(CLKOUTPHY),                   // 1-bit output: XPHY Logic clock
   .CLKOUTPHY_CASC_OUT(CLKOUTPHY_CASC_OUT), // 1-bit output: XPLL CLKOUTPHY cascade output
   .DO(DO),                                 // 16-bit output: DRP data output
   .DRDY(DRDY),                             // 1-bit output: DRP ready
   .LOCKED(LOCKED),                         // 1-bit output: LOCK
   .LOCKED1_DESKEW(LOCKED1_DESKEW),         // 1-bit output: LOCK DESKEW PD1
   .LOCKED2_DESKEW(LOCKED2_DESKEW),         // 1-bit output: LOCK DESKEW PD2
   .LOCKED_FB(LOCKED_FB),                   // 1-bit output: LOCK FEEDBACK
   .PSDONE(PSDONE),                         // 1-bit output: Phase shift done
   .CLKFB1_DESKEW(CLKFB1_DESKEW),           // 1-bit input: Secondary clock input to PD1
   .CLKFB2_DESKEW(CLKFB2_DESKEW),           // 1-bit input: Secondary clock input to PD2
   .CLKIN(CLKIN),                           // 1-bit input: Primary clock
   .CLKIN1_DESKEW(CLKIN1_DESKEW),           // 1-bit input: Primary clock input to PD1
   .CLKIN2_DESKEW(CLKIN2_DESKEW),           // 1-bit input: Primary clock input to PD2
   .CLKOUTPHYEN(CLKOUTPHYEN),               // 1-bit input: CLKOUTPHY enable
   .CLKOUTPHY_CASC_IN(CLKOUTPHY_CASC_IN),   // 1-bit input: XPLL CLKOUTPHY cascade input
   .DADDR(DADDR),                           // 7-bit input: DRP address
   .DCLK(DCLK),                             // 1-bit input: DRP clock
   .DEN(DEN),                               // 1-bit input: DRP enable
   .DI(DI),                                 // 16-bit input: DRP data input
   .DWE(DWE),                               // 1-bit input: DRP write enable
   .PSCLK(PSCLK),                           // 1-bit input: Phase shift clock
   .PSEN(PSEN),                             // 1-bit input: Phase shift enable
   .PSINCDEC(PSINCDEC),                     // 1-bit input: Phase shift increment/decrement
   .PWRDWN(PWRDWN),                         // 1-bit input: Power-down
   .RST(RST)                                // 1-bit input: Reset
);

// End of XPLL_inst instantiation

Related Information

  • Versal Adaptive SoC Clocking Resources Architecture Manual (AM003)