Revision History - Revision History - 6.0 English - PG065

Clocking Wizard LogiCORE IP Product Guide (PG065)

Document_ID
PG065
Release_Date
2022-04-20
Version
6.0 English

The following table shows the revision history for this document.

Date

Version

Revision

04/20/2022

6.0

• Added the Artix UltraSale and UltraScale+ Data sheets support in Maximum Frequencies .

• Updated the content in the MMCM Counter Cascading section.

• Updated the note in the Example for Dynamic Reconfiguration through AXI4-Lite section.

08/06/2021

6.0

• Updated output clock ports in Table: Clocking Wizard I/O .

• Added note to Clock Out of Range .

• Added Optimal Clocking Structure .

• Added bullet to Selecting Clocking Features .

• Updated note about fractional divide values to Configuring Output Clocks .

• Added note to Debug for Dynamic Reconfiguration .

03/18/2021

6.0

• Added note to Table: Clocking Wizard I/O and Table: Clock Configuration Registers .

• Updated the number of clock cycles in the Clock Stop section.

• Added content to the Dynamic Reconfiguration through AXI4-Lite section.

• Added a description to the command line in the Required Constraints section.

• Updated settings in step 3 of Safe Clock Startup Timing Failures for UltraScale and UltraScale+ Devices .

02/05/2020

6.0

• Updated IP Facts .

• Updated binary in note in Example for Dynamic Reconfiguration through AXI4-Lite .

02/25/2019

6.0

• Added note explaining that the Port Renaming tab has been removed in Selecting Clocking Features .

• Added note about OVERRIDE_PRIMITIVE parameter in Overriding Calculated Parameters .

• Added note about Dynamic Reconfiguration in the DRP interface in Example for Dynamic Reconfiguration Using Write to DRP .

04/04/2018

6.0

• Updated for core version

• Updated phase alignment feature in Selecting Clocking Features

• Updated Configuring Output Clocks section in Design Flow Steps

10/04/2017

5.4

• Added Wiki link of clock framework for Linux Operating System

• Updated for minor corrections

04/05/2017

5.4

• Updated for core version

• Updated IP GUI screens in Design Flow Steps

10/05/2016

5.3

• Added a special feature AUTO in primitive selection.

• Added Auto Inference section in Design Flow Steps .

06/08/2016

5.3

• Added a sub section heading for the register space.

• Segregated the Clocking Wizard I/O table contents.

04/06/2016

5.3

• Updated for core version

• Added support for clock monitoring.

• Added the write DRP feature for non-utilization of DSP resources in dynamic reconfiguration.

• Consolidated the redundant bits of clock configuration register 23.

11/18/2015

5.2

• Added support for UltraScale+ architecture-based devices.

09/30/2015

5.2

• Updated for core version and IP GUI screens

• Removed the VHDL support for example design and simulation files

• Removed the unsupported Port-Renaming Tab from GUI in IP Integrator

04/01/2015

5.1

• Added the Minimum Input frequencies for MMCM and PLL for Virtex-7 devices.

• Added an example describing the reference steps when using the AXI Interface for using the dynamic reconfiguration interface.

10/01/2014

5.1

Added UltraScale architecture support and User Parameters mapping table.

10/01/2014

5.1

Added UltraScale architecture support and User Parameters mapping table.

04/02/2014

5.1

Updated Configuring Output Clock section. Added Resource utilization for AXI4-Lite interface using Kintex-7 device.

12/18/2013

5.1

Added UltraScale Architecture support.

10/02/2013

5.1

Updated for to synch doc version with core version. Added Migration information.

03/20/2013

1.3

Updated for core version, added XCI parameters and Safe Clock Startup diagrams and waveforms.

12/18/2012

1.2

Updated for core version, active-Low RESET support, and Vivado GUI screens.

10/16/2012

1.1

Updated for core version and Vivado GUI screens.

07/25/2012

1.0

Initial release of Product Guide, replacing DS709 and UG521.