The following table shows the revision history for this document.
Date |
Version |
Revision |
---|---|---|
04/26/2022 |
5.1 |
• active_lanes port added when CSI-2 Controller Register Interface Disabled • ZCU102 Application Example Design Overview enhanced to support 4K60 on HDMI output. |
11/17/2021 |
5.1 |
• Updated examples in Clocking section. • Updated Pixel Format and Include Video Format Bridge (VFB) options in Configuration Tab . • Updated This Figure . |
07/14/2021 |
5.1 |
• Added Tclk-Post Requirement in Overview . • Added a new note for line rates that are >1500 in Designing with the Subsystem . • Added a new parameter in Configuration Tab . • Updated Table: Vivado IDE Parameter to User Parameter Relationship . • Updated the Running the Design on Hardware section. • Updated Implementing the Example Design section. • Updated Hardware Validation section. |
01/08/2021 |
5.1 |
• General updates and corrections for Versal ACAP support. • Revised examples in Clocking section. • Added YUV420-8bit support. |
07/16/2020 |
5.0 |
Added support for Versal ACAP. |
06/12/2020 |
5.0 |
• Updated the register space information to include VCX Frame Error bit in the IER • Updated the Interoperability testing for UltraScale+ ™ devices. • Example Design for Vitis updated. |
11/22/2019 |
4.1 |
• Updated the register space information to include ISR and IER bits for skewcalhs. • Added Application example design for SP701 board. • Added CSI2 Controller Register Interface GUI option to aid resource optimization. • Removed AXI IIC Option. |
07/02/2019 |
4.0 |
• Extended line rate support up to 2500 Mb/s. • Added support for Deskew sequence detection at MIPI D-PHY for UltraScale+ devices. • Corrected the doc version. |
05/22/2019 |
4.1 |
• Updated the minimum video clock requirement in chapter 3. • Added MIPI CSI2 RX Subsystem Latency Calculation. • Corrected Data corruption for certain word counts during RAW20 data type reception. |
12/05/2018 |
4.0 |
• Updated video_out_tdest and emb_nonimg_tdest port size. • Updated Table 2-5 to include VCX Frame Error register, Image Information 1, and Image Information 2 Registers for VC4 to VC15. • Updated Table 1-1 to include RAW16, RAW20, and YUV 422 10 bit data types. • Updated Table 4-1 User Parameters. • Included new GUI options for MIPI CSI-2 Standard v2.0 compatibility in the Configuration Tab. • Updated examples in the Pixel Packing for Multiple Data Types section to match the alignment described in AXI4-Stream Video IP and System Design Guide (UG934). |
04/04/2018 |
3.0 |
• ECC and CRC of long packets are made available on TUSER ports of output stream interfaces. • Added support for additional 7 series devices. • Added dynamic configuration capability for IDELAY Tap values in fixed calibration mode of 7 series. |
10/04/2017 |
3.0 |
• Added Application Example Design to demonstrate a full end-to-end system from capture to display on ZCU102 • Added Board automation support for LI-IMX274MIPI-FMC V1.0 FMC model |
04/05/2017 |
2.2 |
• Word Count (WC) corruption limited to current packet. Additional bit in ISR added to report this conditions • MIPI DPHY v3.1 changes integrated |
11/30/2016 |
2.1 |
• Added calibration mode parameters for FIXED and AUTO modes |
10/05/2016 |
2.1 |
• MIPI D-PHY 3.0 changes integrated • Added 7 series support |
04/06/2016 |
2.0 |
• MIPI D-PHY 2.0 changes integrated • Shared logic support • Video Format Bridge core changes to support RAW8 and User Defined Byte-based Data at all times along with the Vivado IDE selected data type. |
11/18/2015 |
1.0 |
Initial Xilinx release. |