XPM_FIFO_AXIS - 2023.1 English

UltraScale Architecture Libraries Guide (UG974)

Document ID
UG974
Release Date
2023-05-17
Version
2023.1 English

Parameterized Macro: AXI Stream FIFO

  • MACRO_GROUP: XPM
  • MACRO_SUBGROUP: XPM_FIFO
  • Families: UltraScale, UltraScale+

Introduction

This macro is used to instantiate AXI Stream FIFO.

AXI Stream FIFO is derived from the XPM_FIFO_SYNC and XPM_FIFO_ASYNC. The AXI Stream protocol uses a two-way valid and ready handshake mechanism. The information source uses the valid signal to show when valid data or control information is available on the channel. The information destination uses the ready signal to show when it can accept the data.

Timing Diagrams

Figure 1. Timing for Read and Write Operations to the AXI Stream FIFO

In the timing diagram above, the information source generates a valid signal to indicate when data is available. The destination generates a ready signal to indicate that it can accept data, and transfer occurs only when both the valid and ready signals are High.

Because the AXI Stream FIFO is derived from XPM_FIFO_SYNC and XPM_FIFO_ASYNC, much of the behavior is common between them. The ready signal is generated based on availability of space in the FIFO and is held high to allow writes to the FIFO. The ready signal is pulled Low only when there is no space in the FIFO left to perform additional writes. The valid signal is generated based on availability of data in the FIFO and is held High to allow reads to be performed from the FIFO. The valid signal is pulled Low only when there is no data available to be read from the FIFO. The information signals are mapped to the din and dout bus of Native interface FIFOs. The width of the AXI FIFO is determined by concatenating all of the information signals of the AXI interface. The information signals include all AXI signals except for the valid and ready handshake signals.

The AXI Stream FIFO operates only in First-Word Fall-Through mode. The First-Word Fall-Through (FWFT) feature provides the ability to look ahead to the next word available from the FIFO without issuing a read operation. When data is available in the FIFO, the first word falls through the FIFO and appears automatically on the output data bus.

Port Descriptions

Port Direction Width Domain Sense Handling if Unused Function
almost_empty_axis Output 1 m_aclk LEVEL_HIGH DoNotCare Almost Empty : When asserted, this signal indicates that only one more read can be performed before the FIFO goes to empty.
almost_full_axis Output 1 s_aclk LEVEL_HIGH DoNotCare Almost Full: When asserted, this signal indicates that only one more write can be performed before the FIFO is full.
dbiterr_axis Output 1 m_aclk LEVEL_HIGH DoNotCare Double Bit Error- Indicates that the ECC decoder detected a double-bit error and data in the FIFO core is corrupted.
injectdbiterr_axis Input 1 s_aclk LEVEL_HIGH 0 Double Bit Error Injection- Injects a double bit error if the ECC feature is used.
injectsbiterr_axis Input 1 s_aclk LEVEL_HIGH 0 Single Bit Error Injection- Injects a single bit error if the ECC feature is used.
m_aclk Input 1 NA EDGE_RISING Active Master Interface Clock: All signals on master interface are sampled on the rising edge of this clock.
m_axis_tdata Output TDATA_WIDTH m_aclk NA Active TDATA: The primary payload that is used to provide the data that is passing across the interface. The width of the data payload is an integer number of bytes.
m_axis_tdest Output TDEST_WIDTH m_aclk NA Active TDEST: Provides routing information for the data stream.
m_axis_tid Output TID_WIDTH m_aclk NA Active TID: The data stream identifier that indicates different streams of data.
m_axis_tkeep Output TDATA_WIDTH / 8 m_aclk NA Active TKEEP: The byte qualifier that indicates whether the content of the associated byte of TDATA is processed as part of the data stream. Associated bytes that have the TKEEP byte qualifier deasserted are null bytes and can be removed from the data stream. For a 64-bit DATA, bit 0 corresponds to the least significant byte on DATA, and bit 7 corresponds to the most significant byte. For example:
  • KEEP[0] = 1b, DATA[7:0] is not a NULL byte
  • KEEP[7] = 0b, DATA[63:56] is a NULL byte
m_axis_tlast Output 1 m_aclk LEVEL_HIGH Active TLAST: Indicates the boundary of a packet.
m_axis_tready Input 1 m_aclk LEVEL_HIGH Active TREADY: Indicates that the slave can accept a transfer in the current cycle.
m_axis_tstrb Output TDATA_WIDTH / 8 m_aclk NA Active TSTRB: The byte qualifier that indicates whether the content of the associated byte of TDATA is processed as a data byte or a position byte. For a 64-bit DATA, bit 0 corresponds to the least significant byte on DATA, and bit 0 corresponds to the least significant byte on DATA, and bit 7 corresponds to the most significant byte. For example:
  • STROBE[0] = 1b, DATA[7:0] is valid
  • STROBE[7] = 0b, DATA[63:56] is not valid
m_axis_tuser Output TUSER_WIDTH m_aclk NA Active TUSER: The user-defined sideband information that can be transmitted alongside the data stream.
m_axis_tvalid Output 1 m_aclk LEVEL_HIGH Active TVALID: Indicates that the master is driving a valid transfer.
  • A transfer takes place when both TVALID and TREADY are asserted
prog_empty_axis Output 1 m_aclk LEVEL_HIGH DoNotCare

Programmable Empty- This signal is asserted when the number of words in the FIFO is less than or equal to the programmable empty threshold value.

It is de-asserted when the number of words in the FIFO exceeds the programmable empty threshold value.

prog_full_axis Output 1 s_aclk LEVEL_HIGH DoNotCare

Programmable Full: This signal is asserted when the number of words in the FIFO is greater than or equal to the programmable full threshold value.

It is de-asserted when the number of words in the FIFO is less than the programmable full threshold value.

rd_data_count_axis Output RD_DATA_COUNT_WIDTH m_aclk NA DoNotCare Read Data Count- This bus indicates the number of words available for reading in the FIFO.
s_aclk Input 1 NA EDGE_RISING Active Slave Interface Clock: All signals on slave interface are sampled on the rising edge of this clock.
s_aresetn Input 1 NA LEVEL_LOW Active Active low asynchronous reset.
s_axis_tdata Input TDATA_WIDTH s_aclk NA Active TDATA: The primary payload that is used to provide the data that is passing across the interface. The width of the data payload is an integer number of bytes.
s_axis_tdest Input TDEST_WIDTH s_aclk NA Active TDEST: Provides routing information for the data stream.
s_axis_tid Input TID_WIDTH s_aclk NA Active TID: The data stream identifier that indicates different streams of data.
s_axis_tkeep Input TDATA_WIDTH / 8 s_aclk NA Active TKEEP: The byte qualifier that indicates whether the content of the associated byte of TDATA is processed as part of the data stream. Associated bytes that have the TKEEP byte qualifier deasserted are null bytes and can be removed from the data stream. For a 64-bit DATA, bit 0 corresponds to the least significant byte on DATA, and bit 7 corresponds to the most significant byte. For example:
  • KEEP[0] = 1b, DATA[7:0] is not a NULL byte
  • KEEP[7] = 0b, DATA[63:56] is a NULL byte
s_axis_tlast Input 1 s_aclk LEVEL_HIGH Active TLAST: Indicates the boundary of a packet.
s_axis_tready Output 1 s_aclk LEVEL_HIGH Active TREADY: Indicates that the slave can accept a transfer in the current cycle.
s_axis_tstrb Input TDATA_WIDTH / 8 s_aclk NA Active TSTRB: The byte qualifier that indicates whether the content of the associated byte of TDATA is processed as a data byte or a position byte. For a 64-bit DATA, bit 0 corresponds to the least significant byte on DATA, and bit 0 corresponds to the least significant byte on DATA, and bit 7 corresponds to the most significant byte. For example:
  • STROBE[0] = 1b, DATA[7:0] is valid
  • STROBE[7] = 0b, DATA[63:56] is not valid
s_axis_tuser Input TUSER_WIDTH s_aclk NA Active TUSER: The user-defined sideband information that can be transmitted alongside the data stream.
s_axis_tvalid Input 1 s_aclk LEVEL_HIGH Active TVALID: Indicates that the master is driving a valid transfer.
  • A transfer takes place when both TVALID and TREADY are asserted
sbiterr_axis Output 1 m_aclk LEVEL_HIGH DoNotCare Single Bit Error- Indicates that the ECC decoder detected and fixed a single-bit error.
wr_data_count_axis Output WR_DATA_COUNT_WIDTH s_aclk NA DoNotCare Write Data Count: This bus indicates the number of words written into the FIFO.

Design Entry Method

Instantiation Yes
Inference No
IP and IP Integrator Catalog No

Available Attributes

Attribute Type Allowed Values Default Description
CASCADE_HEIGHT DECIMAL 0 to 64 0

0- No Cascade Height, Allow Vivado Synthesis to choose.

1 or more - Vivado Synthesis sets the specified value as Cascade Height.

CDC_SYNC_STAGES DECIMAL 2 to 8 2

Specifies the number of synchronization stages on the CDC path.

Applicable only if CLOCKING_MODE = "independent_clock"

CLOCKING_MODE STRING "common_clock", "independent_clock" "common_clock" Designate whether AXI Stream FIFO is clocked with a common clock or with independent clocks-
  • "common_clock"- Common clocking; clock both write and read domain s_aclk
  • "independent_clock"- Independent clocking; clock write domain with s_aclk and read domain with m_aclk
ECC_MODE STRING "no_ecc", "en_ecc" "no_ecc"
  • "no_ecc" - Disables ECC
  • "en_ecc" - Enables both ECC Encoder and Decoder
NOTE: ECC_MODE should be "no_ecc" if FIFO_MEMORY_TYPE is set to "auto". Violating this may result incorrect behavior.
FIFO_DEPTH DECIMAL 16 to 4194304 2048 Defines the AXI Stream FIFO Write Depth, must be power of two NOTE: The maximum FIFO size (width x depth) is limited to 150-Megabits.
FIFO_MEMORY_TYPE STRING "auto", "block", "distributed", "ultra" "auto" Designate the fifo memory primitive (resource type) to use-
  • "auto"- Allow Vivado Synthesis to choose
  • "block"- Block RAM FIFO
  • "distributed"- Distributed RAM FIFO
  • "ultra"- URAM FIFO
NOTE: There may be a behavior mismatch if Block RAM or Ultra RAM specific features, like ECC or Asymmetry, are selected with FIFO_MEMORY_TYPE set to "auto".
PACKET_FIFO STRING "false", "true" "false"
  • "true"- Enables Packet FIFO mode
  • "false"- Disables Packet FIFO mode
PROG_EMPTY_THRESH DECIMAL 5 to 4194301 10

Specifies the minimum number of read words in the FIFO at or below which prog_empty is asserted.

  • Min_Value = 5
  • Max_Value = FIFO_WRITE_DEPTH - 5
NOTE: The default threshold value is dependent on default FIFO_WRITE_DEPTH value. If FIFO_WRITE_DEPTH value is changed, ensure the threshold value is within the valid range though the programmable flags are not used.
PROG_FULL_THRESH DECIMAL 5 to 4194301 10

Specifies the maximum number of write words in the FIFO at or above which prog_full is asserted.

  • Min_Value = 5 + CDC_SYNC_STAGES
  • Max_Value = FIFO_WRITE_DEPTH - 5
NOTE: The default threshold value is dependent on default FIFO_WRITE_DEPTH value. If FIFO_WRITE_DEPTH value is changed, ensure the threshold value is within the valid range though the programmable flags are not used.
RD_DATA_COUNT_WIDTH DECIMAL 1 to 23 1 Specifies the width of rd_data_count_axis. To reflect the correct value, the width should be log2(FIFO_DEPTH)+1.
RELATED_CLOCKS DECIMAL 0 to 1 0

Specifies if the s_aclk and m_aclk are related having the same source but different clock ratios.

Applicable only if CLOCKING_MODE = "independent_clock"
SIM_ASSERT_CHK DECIMAL 0 to 1 0

0- Disable simulation message reporting. Messages related to potential misuse will not be reported.

1- Enable simulation message reporting. Messages related to potential misuse will be reported.

TDATA_WIDTH DECIMAL 8 to 2048 32 Defines the width of the TDATA port, s_axis_tdata and m_axis_tdata NOTE: The maximum FIFO size (width x depth) is limited to 150-Megabits.
TDEST_WIDTH DECIMAL 1 to 32 1 Defines the width of the TDEST port, s_axis_tdest and m_axis_tdest
TID_WIDTH DECIMAL 1 to 32 1 Defines the width of the ID port, s_axis_tid and m_axis_tid
TUSER_WIDTH DECIMAL 1 to 4086 1 Defines the width of the TUSER port, s_axis_tuser and m_axis_tuser
USE_ADV_FEATURES STRING String "1000"

Enables almost_empty_axis, rd_data_count_axis, prog_empty_axis, almost_full_axis, wr_data_count_axis, prog_full_axis sideband signals.

  • Setting USE_ADV_FEATURES[1] to 1 enables prog_full flag; Default value of this bit is 0
  • Setting USE_ADV_FEATURES[2] to 1 enables wr_data_count; Default value of this bit is 0
  • Setting USE_ADV_FEATURES[3] to 1 enables almost_full flag; Default value of this bit is 0
  • Setting USE_ADV_FEATURES[9] to 1 enables prog_empty flag; Default value of this bit is 0
  • Setting USE_ADV_FEATURES[10] to 1 enables rd_data_count; Default value of this bit is 0
  • Setting USE_ADV_FEATURES[11] to 1 enables almost_empty flag; Default value of this bit is 0
WR_DATA_COUNT_WIDTH DECIMAL 1 to 23 1 Specifies the width of wr_data_count_axis. To reflect the correct value, the width should be log2(FIFO_DEPTH)+1.

VHDL Instantiation Template

Unless they already exist, copy the following two statements and paste them before the entity declaration.
Library xpm;
use xpm.vcomponents.all;

-- xpm_fifo_axis: AXI Stream FIFO
-- Xilinx Parameterized Macro, version 2023.1

xpm_fifo_axis_inst : xpm_fifo_axis
generic map (
   CASCADE_HEIGHT => 0,             -- DECIMAL
   CDC_SYNC_STAGES => 2,            -- DECIMAL
   CLOCKING_MODE => "common_clock", -- String
   ECC_MODE => "no_ecc",            -- String
   FIFO_DEPTH => 2048,              -- DECIMAL
   FIFO_MEMORY_TYPE => "auto",      -- String
   PACKET_FIFO => "false",          -- String
   PROG_EMPTY_THRESH => 10,         -- DECIMAL
   PROG_FULL_THRESH => 10,          -- DECIMAL
   RD_DATA_COUNT_WIDTH => 1,        -- DECIMAL
   RELATED_CLOCKS => 0,             -- DECIMAL
   SIM_ASSERT_CHK => 0,             -- DECIMAL; 0=disable simulation messages, 1=enable simulation messages
   TDATA_WIDTH => 32,               -- DECIMAL
   TDEST_WIDTH => 1,                -- DECIMAL
   TID_WIDTH => 1,                  -- DECIMAL
   TUSER_WIDTH => 1,                -- DECIMAL
   USE_ADV_FEATURES => "1000",      -- String
   WR_DATA_COUNT_WIDTH => 1         -- DECIMAL
)
port map (
   almost_empty_axis => almost_empty_axis,   -- 1-bit output: Almost Empty : When asserted, this signal
                                             -- indicates that only one more read can be performed before
                                             -- the FIFO goes to empty.

   almost_full_axis => almost_full_axis,     -- 1-bit output: Almost Full: When asserted, this signal
                                             -- indicates that only one more write can be performed before
                                             -- the FIFO is full.

   dbiterr_axis => dbiterr_axis,             -- 1-bit output: Double Bit Error- Indicates that the ECC
                                             -- decoder detected a double-bit error and data in the FIFO
                                             -- core is corrupted.

   m_axis_tdata => m_axis_tdata,             -- TDATA_WIDTH-bit output: TDATA: The primary payload that is
                                             -- used to provide the data that is passing across the
                                             -- interface. The width of the data payload is an integer
                                             -- number of bytes.

   m_axis_tdest => m_axis_tdest,             -- TDEST_WIDTH-bit output: TDEST: Provides routing information
                                             -- for the data stream.

   m_axis_tid => m_axis_tid,                 -- TID_WIDTH-bit output: TID: The data stream identifier that
                                             -- indicates different streams of data.

   m_axis_tkeep => m_axis_tkeep,             -- TDATA_WIDTH/8-bit output: TKEEP: The byte qualifier that
                                             -- indicates whether the content of the associated byte of
                                             -- TDATA is processed as part of the data stream. Associated
                                             -- bytes that have the TKEEP byte qualifier deasserted are null
                                             -- bytes and can be removed from the data stream. For a 64-bit
                                             -- DATA, bit 0 corresponds to the least significant byte on
                                             -- DATA, and bit 7 corresponds to the most significant byte.
                                             -- For example: KEEP[0] = 1b, DATA[7:0] is not a NULL byte
                                             -- KEEP[7] = 0b, DATA[63:56] is a NULL byte

   m_axis_tlast => m_axis_tlast,             -- 1-bit output: TLAST: Indicates the boundary of a packet.
   m_axis_tstrb => m_axis_tstrb,             -- TDATA_WIDTH/8-bit output: TSTRB: The byte qualifier that
                                             -- indicates whether the content of the associated byte of
                                             -- TDATA is processed as a data byte or a position byte. For a
                                             -- 64-bit DATA, bit 0 corresponds to the least significant byte
                                             -- on DATA, and bit 0 corresponds to the least significant byte
                                             -- on DATA, and bit 7 corresponds to the most significant byte.
                                             -- For example: STROBE[0] = 1b, DATA[7:0] is valid STROBE[7] =
                                             -- 0b, DATA[63:56] is not valid

   m_axis_tuser => m_axis_tuser,             -- TUSER_WIDTH-bit output: TUSER: The user-defined sideband
                                             -- information that can be transmitted alongside the data
                                             -- stream.

   m_axis_tvalid => m_axis_tvalid,           -- 1-bit output: TVALID: Indicates that the master is driving a
                                             -- valid transfer. A transfer takes place when both TVALID and
                                             -- TREADY are asserted

   prog_empty_axis => prog_empty_axis,       -- 1-bit output: Programmable Empty- This signal is asserted
                                             -- when the number of words in the FIFO is less than or equal
                                             -- to the programmable empty threshold value. It is de-asserted
                                             -- when the number of words in the FIFO exceeds the
                                             -- programmable empty threshold value.

   prog_full_axis => prog_full_axis,         -- 1-bit output: Programmable Full: This signal is asserted
                                             -- when the number of words in the FIFO is greater than or
                                             -- equal to the programmable full threshold value. It is
                                             -- de-asserted when the number of words in the FIFO is less
                                             -- than the programmable full threshold value.

   rd_data_count_axis => rd_data_count_axis, -- RD_DATA_COUNT_WIDTH-bit output: Read Data Count- This bus
                                             -- indicates the number of words available for reading in the
                                             -- FIFO.

   s_axis_tready => s_axis_tready,           -- 1-bit output: TREADY: Indicates that the slave can accept a
                                             -- transfer in the current cycle.

   sbiterr_axis => sbiterr_axis,             -- 1-bit output: Single Bit Error- Indicates that the ECC
                                             -- decoder detected and fixed a single-bit error.

   wr_data_count_axis => wr_data_count_axis, -- WR_DATA_COUNT_WIDTH-bit output: Write Data Count: This bus
                                             -- indicates the number of words written into the FIFO.

   injectdbiterr_axis => injectdbiterr_axis, -- 1-bit input: Double Bit Error Injection- Injects a double
                                             -- bit error if the ECC feature is used.

   injectsbiterr_axis => injectsbiterr_axis, -- 1-bit input: Single Bit Error Injection- Injects a single
                                             -- bit error if the ECC feature is used.

   m_aclk => m_aclk,                         -- 1-bit input: Master Interface Clock: All signals on master
                                             -- interface are sampled on the rising edge of this clock.

   m_axis_tready => m_axis_tready,           -- 1-bit input: TREADY: Indicates that the slave can accept a
                                             -- transfer in the current cycle.

   s_aclk => s_aclk,                         -- 1-bit input: Slave Interface Clock: All signals on slave
                                             -- interface are sampled on the rising edge of this clock.

   s_aresetn => s_aresetn,                   -- 1-bit input: Active low asynchronous reset.
   s_axis_tdata => s_axis_tdata,             -- TDATA_WIDTH-bit input: TDATA: The primary payload that is
                                             -- used to provide the data that is passing across the
                                             -- interface. The width of the data payload is an integer
                                             -- number of bytes.

   s_axis_tdest => s_axis_tdest,             -- TDEST_WIDTH-bit input: TDEST: Provides routing information
                                             -- for the data stream.

   s_axis_tid => s_axis_tid,                 -- TID_WIDTH-bit input: TID: The data stream identifier that
                                             -- indicates different streams of data.

   s_axis_tkeep => s_axis_tkeep,             -- TDATA_WIDTH/8-bit input: TKEEP: The byte qualifier that
                                             -- indicates whether the content of the associated byte of
                                             -- TDATA is processed as part of the data stream. Associated
                                             -- bytes that have the TKEEP byte qualifier deasserted are null
                                             -- bytes and can be removed from the data stream. For a 64-bit
                                             -- DATA, bit 0 corresponds to the least significant byte on
                                             -- DATA, and bit 7 corresponds to the most significant byte.
                                             -- For example: KEEP[0] = 1b, DATA[7:0] is not a NULL byte
                                             -- KEEP[7] = 0b, DATA[63:56] is a NULL byte

   s_axis_tlast => s_axis_tlast,             -- 1-bit input: TLAST: Indicates the boundary of a packet.
   s_axis_tstrb => s_axis_tstrb,             -- TDATA_WIDTH/8-bit input: TSTRB: The byte qualifier that
                                             -- indicates whether the content of the associated byte of
                                             -- TDATA is processed as a data byte or a position byte. For a
                                             -- 64-bit DATA, bit 0 corresponds to the least significant byte
                                             -- on DATA, and bit 0 corresponds to the least significant byte
                                             -- on DATA, and bit 7 corresponds to the most significant byte.
                                             -- For example: STROBE[0] = 1b, DATA[7:0] is valid STROBE[7] =
                                             -- 0b, DATA[63:56] is not valid

   s_axis_tuser => s_axis_tuser,             -- TUSER_WIDTH-bit input: TUSER: The user-defined sideband
                                             -- information that can be transmitted alongside the data
                                             -- stream.

   s_axis_tvalid => s_axis_tvalid            -- 1-bit input: TVALID: Indicates that the master is driving a
                                             -- valid transfer. A transfer takes place when both TVALID and
                                             -- TREADY are asserted

);

-- End of xpm_fifo_axis_inst instantiation

Verilog Instantiation Template


// xpm_fifo_axis: AXI Stream FIFO
// Xilinx Parameterized Macro, version 2023.1

xpm_fifo_axis #(
   .CASCADE_HEIGHT(0),             // DECIMAL
   .CDC_SYNC_STAGES(2),            // DECIMAL
   .CLOCKING_MODE("common_clock"), // String
   .ECC_MODE("no_ecc"),            // String
   .FIFO_DEPTH(2048),              // DECIMAL
   .FIFO_MEMORY_TYPE("auto"),      // String
   .PACKET_FIFO("false"),          // String
   .PROG_EMPTY_THRESH(10),         // DECIMAL
   .PROG_FULL_THRESH(10),          // DECIMAL
   .RD_DATA_COUNT_WIDTH(1),        // DECIMAL
   .RELATED_CLOCKS(0),             // DECIMAL
   .SIM_ASSERT_CHK(0),             // DECIMAL; 0=disable simulation messages, 1=enable simulation messages
   .TDATA_WIDTH(32),               // DECIMAL
   .TDEST_WIDTH(1),                // DECIMAL
   .TID_WIDTH(1),                  // DECIMAL
   .TUSER_WIDTH(1),                // DECIMAL
   .USE_ADV_FEATURES("1000"),      // String
   .WR_DATA_COUNT_WIDTH(1)         // DECIMAL
)
xpm_fifo_axis_inst (
   .almost_empty_axis(almost_empty_axis),   // 1-bit output: Almost Empty : When asserted, this signal
                                            // indicates that only one more read can be performed before the
                                            // FIFO goes to empty.

   .almost_full_axis(almost_full_axis),     // 1-bit output: Almost Full: When asserted, this signal
                                            // indicates that only one more write can be performed before
                                            // the FIFO is full.

   .dbiterr_axis(dbiterr_axis),             // 1-bit output: Double Bit Error- Indicates that the ECC
                                            // decoder detected a double-bit error and data in the FIFO core
                                            // is corrupted.

   .m_axis_tdata(m_axis_tdata),             // TDATA_WIDTH-bit output: TDATA: The primary payload that is
                                            // used to provide the data that is passing across the
                                            // interface. The width of the data payload is an integer number
                                            // of bytes.

   .m_axis_tdest(m_axis_tdest),             // TDEST_WIDTH-bit output: TDEST: Provides routing information
                                            // for the data stream.

   .m_axis_tid(m_axis_tid),                 // TID_WIDTH-bit output: TID: The data stream identifier that
                                            // indicates different streams of data.

   .m_axis_tkeep(m_axis_tkeep),             // TDATA_WIDTH/8-bit output: TKEEP: The byte qualifier that
                                            // indicates whether the content of the associated byte of TDATA
                                            // is processed as part of the data stream. Associated bytes
                                            // that have the TKEEP byte qualifier deasserted are null bytes
                                            // and can be removed from the data stream. For a 64-bit DATA,
                                            // bit 0 corresponds to the least significant byte on DATA, and
                                            // bit 7 corresponds to the most significant byte. For example:
                                            // KEEP[0] = 1b, DATA[7:0] is not a NULL byte KEEP[7] = 0b,
                                            // DATA[63:56] is a NULL byte

   .m_axis_tlast(m_axis_tlast),             // 1-bit output: TLAST: Indicates the boundary of a packet.
   .m_axis_tstrb(m_axis_tstrb),             // TDATA_WIDTH/8-bit output: TSTRB: The byte qualifier that
                                            // indicates whether the content of the associated byte of TDATA
                                            // is processed as a data byte or a position byte. For a 64-bit
                                            // DATA, bit 0 corresponds to the least significant byte on
                                            // DATA, and bit 0 corresponds to the least significant byte on
                                            // DATA, and bit 7 corresponds to the most significant byte. For
                                            // example: STROBE[0] = 1b, DATA[7:0] is valid STROBE[7] = 0b,
                                            // DATA[63:56] is not valid

   .m_axis_tuser(m_axis_tuser),             // TUSER_WIDTH-bit output: TUSER: The user-defined sideband
                                            // information that can be transmitted alongside the data
                                            // stream.

   .m_axis_tvalid(m_axis_tvalid),           // 1-bit output: TVALID: Indicates that the master is driving a
                                            // valid transfer. A transfer takes place when both TVALID and
                                            // TREADY are asserted

   .prog_empty_axis(prog_empty_axis),       // 1-bit output: Programmable Empty- This signal is asserted
                                            // when the number of words in the FIFO is less than or equal to
                                            // the programmable empty threshold value. It is de-asserted
                                            // when the number of words in the FIFO exceeds the programmable
                                            // empty threshold value.

   .prog_full_axis(prog_full_axis),         // 1-bit output: Programmable Full: This signal is asserted when
                                            // the number of words in the FIFO is greater than or equal to
                                            // the programmable full threshold value. It is de-asserted when
                                            // the number of words in the FIFO is less than the programmable
                                            // full threshold value.

   .rd_data_count_axis(rd_data_count_axis), // RD_DATA_COUNT_WIDTH-bit output: Read Data Count- This bus
                                            // indicates the number of words available for reading in the
                                            // FIFO.

   .s_axis_tready(s_axis_tready),           // 1-bit output: TREADY: Indicates that the slave can accept a
                                            // transfer in the current cycle.

   .sbiterr_axis(sbiterr_axis),             // 1-bit output: Single Bit Error- Indicates that the ECC
                                            // decoder detected and fixed a single-bit error.

   .wr_data_count_axis(wr_data_count_axis), // WR_DATA_COUNT_WIDTH-bit output: Write Data Count: This bus
                                            // indicates the number of words written into the FIFO.

   .injectdbiterr_axis(injectdbiterr_axis), // 1-bit input: Double Bit Error Injection- Injects a double bit
                                            // error if the ECC feature is used.

   .injectsbiterr_axis(injectsbiterr_axis), // 1-bit input: Single Bit Error Injection- Injects a single bit
                                            // error if the ECC feature is used.

   .m_aclk(m_aclk),                         // 1-bit input: Master Interface Clock: All signals on master
                                            // interface are sampled on the rising edge of this clock.

   .m_axis_tready(m_axis_tready),           // 1-bit input: TREADY: Indicates that the slave can accept a
                                            // transfer in the current cycle.

   .s_aclk(s_aclk),                         // 1-bit input: Slave Interface Clock: All signals on slave
                                            // interface are sampled on the rising edge of this clock.

   .s_aresetn(s_aresetn),                   // 1-bit input: Active low asynchronous reset.
   .s_axis_tdata(s_axis_tdata),             // TDATA_WIDTH-bit input: TDATA: The primary payload that is
                                            // used to provide the data that is passing across the
                                            // interface. The width of the data payload is an integer number
                                            // of bytes.

   .s_axis_tdest(s_axis_tdest),             // TDEST_WIDTH-bit input: TDEST: Provides routing information
                                            // for the data stream.

   .s_axis_tid(s_axis_tid),                 // TID_WIDTH-bit input: TID: The data stream identifier that
                                            // indicates different streams of data.

   .s_axis_tkeep(s_axis_tkeep),             // TDATA_WIDTH/8-bit input: TKEEP: The byte qualifier that
                                            // indicates whether the content of the associated byte of TDATA
                                            // is processed as part of the data stream. Associated bytes
                                            // that have the TKEEP byte qualifier deasserted are null bytes
                                            // and can be removed from the data stream. For a 64-bit DATA,
                                            // bit 0 corresponds to the least significant byte on DATA, and
                                            // bit 7 corresponds to the most significant byte. For example:
                                            // KEEP[0] = 1b, DATA[7:0] is not a NULL byte KEEP[7] = 0b,
                                            // DATA[63:56] is a NULL byte

   .s_axis_tlast(s_axis_tlast),             // 1-bit input: TLAST: Indicates the boundary of a packet.
   .s_axis_tstrb(s_axis_tstrb),             // TDATA_WIDTH/8-bit input: TSTRB: The byte qualifier that
                                            // indicates whether the content of the associated byte of TDATA
                                            // is processed as a data byte or a position byte. For a 64-bit
                                            // DATA, bit 0 corresponds to the least significant byte on
                                            // DATA, and bit 0 corresponds to the least significant byte on
                                            // DATA, and bit 7 corresponds to the most significant byte. For
                                            // example: STROBE[0] = 1b, DATA[7:0] is valid STROBE[7] = 0b,
                                            // DATA[63:56] is not valid

   .s_axis_tuser(s_axis_tuser),             // TUSER_WIDTH-bit input: TUSER: The user-defined sideband
                                            // information that can be transmitted alongside the data
                                            // stream.

   .s_axis_tvalid(s_axis_tvalid)            // 1-bit input: TVALID: Indicates that the master is driving a
                                            // valid transfer. A transfer takes place when both TVALID and
                                            // TREADY are asserted

);

// End of xpm_fifo_axis_inst instantiation

Related Information