LDPE - 2022.2 English

Versal Architecture Premium Series Libraries Guide (UG1485)

Document ID
UG1485
Release Date
2022-10-19
Version
2022.2 English

Primitive: Transparent Latch with Clock Enable and Asynchronous Preset

  • PRIMITIVE_GROUP: REGISTER
  • PRIMITIVE_SUBGROUP: LATCH

Introduction

This design element is a transparent data latch with asynchronous preset and gate enable. When the asynchronous preset input (PRE) is active, it overrides the other inputs and presets the data (Q) output High. Q reflects the data (D) input while the gate (G) input and gate enable (GE) are active and PRE is not active. If (GE) is Low, data on (D) cannot be latched. The data on the (D) input during the gate transition is stored in the latch. The data on the (Q) output remains unchanged as long as (G) or (GE) remains Low.

This latch is asynchronously initialized when power is applied. When global set/reset (GSR) is active upon power-up or when GSR is asserted, the value of the INIT attribute is placed on the latch's output.

Logic Table

Inputs Outputs
PRE GE G D Q
1 X X X 1
0 0 X X No Change
0 1 1 D D
0 1 0 X No Change
0 1 D D

Port Descriptions

Port Direction Width Function
D Input 1 Data input
G Input 1 Gate input. Polarity is determined by the IS_G_INVERTED attribute.
GE Input 1 Active-High latch gate enable.
PRE Input 1 Asynchronous preset. Polarity is determined by the IS_PRE_INVERTED attribute.
Q Output 1 Data output

Design Entry Method

Instantiation Yes
Inference Yes
IP and IP Integrator Catalog No

Available Attributes

Attribute Type Allowed Values Default Description
INIT BINARY 1'b1, 1'b0 1'b1 Sets the initial value of Q output after configuration or when GSR is asserted.
Programmable Inversion Attributes: Specifies whether or not to use the optional inversion on specific pins of this component to change the active polarity of the pin function. When set to 1 on a gate pin (G), it creates an active-Low latch. When set to 1 on other pins, it changes the function to behave active-Low rather than active-High. If an external inverter is specified on one of these associated pins, the Vivado Design Suite will automatically set this attribute during the opt_design stage so that additional logic is not necessary for changing the input polarity.
IS_G_INVERTED BINARY 1'b0 to 1'b1 1'b0 Specifies whether or not to use the optional inversion for the G pin of this component.
IS_PRE_INVERTED BINARY 1'b0 to 1'b1 1'b0 Specifies whether or not to use the optional inversion for the PRE pin of this component.

VHDL Instantiation Template

Unless they already exist, copy the following two statements and paste them before the entity declaration.
Library UNISIM;
use UNISIM.vcomponents.all;

-- LDPE: Transparent Latch with Clock Enable and Asynchronous Preset
--       Versal Premium series
-- Xilinx HDL Language Template, version 2022.2

LDPE_inst : LDPE
generic map (
   INIT => '1',            -- Initial value of latch, '0', '1'
   -- Programmable Inversion Attributes: Specifies the use of the built-in programmable inversion
   IS_G_INVERTED => '0',   -- Optional inversion for G
   IS_PRE_INVERTED => '0'  -- Optional inversion for PRE
)
port map (
   Q => Q,     -- 1-bit output: Data
   D => D,     -- 1-bit input: Data
   G => G,     -- 1-bit input: Gate
   GE => GE,   -- 1-bit input: Gate enable
   PRE => PRE  -- 1-bit input: Asynchronous preset
);

-- End of LDPE_inst instantiation

Verilog Instantiation Template


// LDPE: Transparent Latch with Clock Enable and Asynchronous Preset
//       Versal Premium series
// Xilinx HDL Language Template, version 2022.2

LDPE #(
   .INIT(1'b1),            // Initial value of latch, 1'b0, 1'b1
   // Programmable Inversion Attributes: Specifies the use of the built-in programmable inversion
   .IS_G_INVERTED(1'b0),   // Optional inversion for G
   .IS_PRE_INVERTED(1'b0)  // Optional inversion for PRE
)
LDPE_inst (
   .Q(Q),     // 1-bit output: Data
   .D(D),     // 1-bit input: Data
   .G(G),     // 1-bit input: Gate
   .GE(GE),   // 1-bit input: Gate enable
   .PRE(PRE)  // 1-bit input: Asynchronous preset
);

// End of LDPE_inst instantiation

Related Information

  • Versal ACAP Register Reference Manual (AM012)