Divider Generator 5.1 - 2022.2 English

Vitis Model Composer User Guide (UG1483)

Document ID
UG1483
Release Date
2023-01-13
Version
2022.2 English

The Xilinx Divider Generator block creates a circuit for integer division based on Radix-2 non-restoring division, or High-Radix division with prescaling.

Block Parameters

The Block Parameters dialog box can be invoked by double-clicking the icon in your Simulink® model.

Basic tab
Common Options
Algorithm Type
  • Radix-2: Non-restoring integer division using integer operands, allows a remainder to be generated. This is recommended for operand widths less than around 16 bits. This option supports both unsigned and signed (2’s complement) divisor and dividend inputs.
  • High_Radix: Division with prescaling. This is recommended for operand widths greater than 16 bits, though the implementation requires the use of DSP48 (or variant) primitives. This option only supports signed (2’s complement) divisor and dividend inputs.
  • LutMult: A simple lookup estimate of the reciprocal of the divisor followed by a multiplier. Only the remainder output type is supported because of the bias required in the reciprocal estimate. This bias would introduce an offset (error) if used to create a fractional output. This is recommended for operand widths less than or equal to 12 bits. This implementation uses DSP slices, block RAM, and a small number of FPGA logic primitives (registers and LUTs). For operand widths where either Radix2 or the LUTMult options are possible, the LUTMult offers a solution using fewer FPGA logic resources because of the use of DSP and block RAM primitives. Supports unsigned or two's complement signed numbers.
Output channel
Remainder type
Remainder
Only supported for Radix 2.
Fractional
Determines the number of bits in the fractional port output.
Fractional width
If Fractional Remainder type is selected, this entry determines the number of bits in the fractional port output.
Radix2 Options
Radix2 throughput
Determines the interval in clocks between new data being input (and output). Choices are 1, 2, 4, and 8.
High Radix Options
Detect divide by zero
Determines if the core shall have a division-by-zero indication output port.
AXI Interface
AXI behavior
NonBlocking
Performs an action only when a control packet and a data packet are presented to the block at the same time.
Blocking
Preforms an action when a data packet is presented to the block. The block uses the previous control information.
AXI Implementation emphasis
Resources
Automatic (fully pipelined) or Manual (determined by following field).
Performance
Implementation decisions target the highest speed.
Latency Options
Latency configuration
Automatic (fully pipelined) or Manual (determined by following field).
Latency
This field determines the exact latency from input to output in terms of clock enabled clock cycles.
Optional ports tab
Optional Ports
Divided Channel Ports
Has TUSER
Adds a tuser input port to the dividend channel.
Has TLAST
Adds a tlast output port to the dividend channel.
Divisor Channel Ports
Has TUSER
Adds a tuser input port to the divisor channel.
Has TLAST
Adds a tlast output port to the divisor channel.
ACLKEN
Specifies that the block has a clock enable port (the equivalent of selecting the Has ACLKEN option in the CORE Generator GUI).
ARESETn
Specifies that the block has a reset port. Active-Low synchronous clear. A minimum ARESETn pulse of two cycles is required.
m_axis_dout_tready
Specifies that the block has a dout_tready output port.
Input TLAST combination for output
Determines the behavior of the dout_tlast output port.
Null
Output is null.
Pass_Dividend_TLAST
Pass the value of the dividend_tlast input port to the dout_tlast output port.
Pass Divisor_TLAST
Pass the value of the divisor_tlast input port to the dout_tlast output port.
OR_all_TLASTS
Pass the logical OR of all the present TLAST input ports.
AND_all_TLASTS
Pass the logical AND of all the present TLAST input ports.

Other parameters used by this block are explained in the topic Common Options in Block Parameter Dialog Boxes.

LogiCORE™ Documentation

Divider Generator LogiCORE IP Product Guide (PG151)