Using Force in Batch Mode - 2022.1 English

Vivado Design Suite User Guide: Logic Simulation (UG900)

Document ID
UG900
Release Date
2022-04-21
Version
2022.1 English

The code examples below show how to force a signal to a specified value using the add_force command. A simple verilog circuit is provided. The first example shows the interactive use of the add_force command and the second example shows the scripted use.

Example 1: Adding Force

The following code snippet is a Verilog circuit:

module bot(input in1, in2,output out1);
reg sel;
assign out1 = sel? in1: in2;
endmodule
module top;
reg in1, in2;
wire out1;
bot I1(in1, in2, out1);
initial
begin
    #10 in1 = 1'b1; in2 = 1'b0;
    #10 in1 = 1'b0; in2 = 1'b1;
end
initial
    $monitor("out1 = %b\n", out1);
endmodule

You can invoke the following commands to observe the effect of add_force:

xelab -vlog tmp.v -debug all
xsim work.top

At the command prompt, type:

add_force /top/I1/sel 1
run 10
add_force /top/I1/sel 0
run all

You can use the add_force Tcl command to force a signal, wire, or register to a specified value:

add_force [-radix <arg>] [-repeat_every <arg>] [-cancel_after <arg>] [-quiet] 
[-verbose] <hdl_object> <values>...

For more info on this and other Tcl commands, see the Vivado Design Suite Tcl Command Reference Guide (UG835).

Example 2: Scripted Use of add_force with remove_forces

The following is an example Verilog file, top.v, which instantiates a counter. You can use this file in the following command example.

module counter(input clk,reset,updown,output [4:0] out1);
reg [4:0] r1;
always@(posedge clk)
begin
    if(reset)
        r1 <= 0;
    else
        if(updown)
            r1 <= r1 + 1;
        else
            r1 <= r1 - 1;
end
assign out1 = r1;
endmodule
module top;
reg clk;
reg reset;
reg updown;
wire [4:0] out1;
counter I1(clk, reset, updown, out1);
initial
begin
    reset = 1;
    #20 reset = 0;
end
initial
begin
    updown = 1; clk = 0;
end
initial
    #500 $finish;
initial
    $monitor("out1 = %b\n", out1);
endmodule

Command Example

  1. Create a file called add_force.tcl with following command:
    create_project add_force -force
    add_files top.v
    set_property top top [get_filesets sim_1]
    set_property -name xelab.more_options -value {-debug all} -objects [get_filesets 
    sim_1]
    set_property runtime {0} [get_filesets sim_1]
    launch_simulation -simset sim_1 -mode behavioral
    add_wave /top/*
  2. Invoke the Vivado Design Suite in Tcl mode, and source the add_force.tcl file.
  3. In the Tcl Console, type:
    set force1 [add_force clk {0 1} {1 2} -repeat_every 3 -cancel_after 500]
    set force2 [add_force updown {0 10} {1 20} -repeat_every 30]
    run 100

    Observe that the value of out1 increments as well as decrements in the Wave window. You can observe the waveforms in the Vivado IDE using the start_gui command.

    Observe the value of updown signal in the Wave window.

  4. In the Tcl Console, type:
    remove_forces $force2
    run 100

    Observe that only the value of out1 increments.

  5. In the Tcl Console, type:
    remove_forces $force1
    run 100

    Observe that the value of out1 is not changing because the clk signal is not toggling.