Primitive: 64-Deep by 1-Wide Dual Port Static Synchronous RAM
- PRIMITIVE_GROUP: CLB
- PRIMITIVE_SUBGROUP: LUTRAM
Introduction
This design element is a 64-bit deep by 1-bit wide static dual port random access memory with synchronous write capability. The device has two separate address ports: the read address (DPRA5:DPRA0) and the write address (A5:A0). These two address ports are completely asynchronous. The read address controls the location of the data driven out of the output pin (DPO), and the write address controls the destination of a valid write transaction. When the write enable (WE) is Low, transitions on the write clock (WCLK) are ignored and data stored in the RAM is not affected.
When WE is High, any positive transition on WCLK loads the data on the data input (D) into the memory cell selected by the 6-bit (A0:A5) write address. For predictable performance, write address and data inputs must be stable before a Low-to-High WCLK transition. This RAM block assumes an active-High WCLK. WCLK can be active-High or active-Low. Any inverter placed on the WCLK input net is absorbed into the block.
The SPO output reflects the data in the memory cell addressed by A5:A0. The DPO output reflects the data in the memory cell addressed by DPRA5:DPRA0. The write process is not affected by the address on the read address port.
You can use the INIT attribute to specify the initial contents of the RAM. If left unspecified, the initial contents default to all zeros.
Logic Table
Inputs | Outputs | |||
---|---|---|---|---|
WE (mode) | WCLK | D | SPO | DPO |
0 (read) | X | X | data_a | data_d |
1 (read) | 0 | X | data_a | data_d |
1 (read) | 1 | X | data_a | data_d |
1 (write) | ↑ | D | D | data_d |
1 (read) | ↓ | X | data_a | data_d |
data_a = memory cell addressed by bits A5:A0 data_d = memory cell addressed by bits DPRA5:DPRA0 |
Design Entry Method
Instantiation | Yes |
Inference | Recommended |
IP Catalog | No |
Available Attributes
Attribute | Type | Allowed Values | Default | Description |
---|---|---|---|---|
INIT | HEX | Any 64-bit value | All zeros | Specifies the initial contents of the RAM. |
IS_WCLK_INVERTED | BINARY | 1'b0 to 1'b1 | 1'b0 | Specifies whether or not to use the optional inversion on the WCLK pin. |
VHDL Instantiation Template
Library UNISIM;
use UNISIM.vcomponents.all;
-- RAM64X1D: 64 x 1 positive edge write, asynchronous read
-- dual-port distributed RAM
-- Versal Prime series
-- Xilinx HDL Language Template, version 2022.1
RAM64X1D_inst : RAM64X1D
generic map (
INIT => X"0000000000000000", -- Initial contents of RAM
IS_WCLK_INVERTED => '0') -- Specifies active high/low WCLK
port map (
DPO => DPO, -- Read-only 1-bit data output
SPO => SPO, -- R/W 1-bit data output
A0 => A0, -- R/W address[0] input bit
A1 => A1, -- R/W address[1] input bit
A2 => A2, -- R/W address[2] input bit
A3 => A3, -- R/W address[3] input bit
A4 => A4, -- R/W address[4] input bit
A5 => A5, -- R/W address[5] input bit
D => D, -- Write 1-bit data input
DPRA0 => DPRA0, -- Read-only address[0] input bit
DPRA1 => DPRA1, -- Read-only address[1] input bit
DPRA2 => DPRA2, -- Read-only address[2] input bit
DPRA3 => DPRA3, -- Read-only address[3] input bit
DPRA4 => DPRA4, -- Read-only address[4] input bit
DPRA5 => DPRA5, -- Read-only address[5] input bit
WCLK => WCLK, -- Write clock input
WE => WE -- Write enable input
);
-- End of RAM64X1D_inst instantiation
Verilog Instantiation Template
// RAM64X1D: 64 x 1 positive edge write, asynchronous read dual-port
// distributed RAM (Mapped to two LUT6s)
// Versal Prime series
// Xilinx HDL Language Template, version 2022.1
RAM64X1D #(
.INIT(64'h0000000000000000), // Initial contents of RAM
.IS_WCLK_INVERTED(1'b0) // Specifies active high/low WCLK
) RAM64X1D_inst (
.DPO(DPO), // Read-only 1-bit data output
.SPO(SPO), // Rw/ 1-bit data output
.A0(A0), // Rw/ address[0] input bit
.A1(A1), // Rw/ address[1] input bit
.A2(A2), // Rw/ address[2] input bit
.A3(A3), // Rw/ address[3] input bit
.A4(A4), // Rw/ address[4] input bit
.A5(A5), // Rw/ address[5] input bit
.D(D), // Write 1-bit data input
.DPRA0(DPRA0), // Read-only address[0] input bit
.DPRA1(DPRA1), // Read-only address[1] input bit
.DPRA2(DPRA2), // Read-only address[2] input bit
.DPRA3(DPRA3), // Read-only address[3] input bit
.DPRA4(DPRA4), // Read-only address[4] input bit
.DPRA5(DPRA5), // Read-only address[5] input bit
.WCLK(WCLK), // Write clock input
.WE(WE) // Write enable input
);
// End of RAM64X1D_inst instantiation
Related Information
- Versal ACAP Configurable Logic Block Architecture Manual (AM005)