Primitive: D Flip-Flop with Clock Enable and Synchronous Reset
- PRIMITIVE_GROUP: REGISTER
- PRIMITIVE_SUBGROUP: SDR
Introduction
This design element is a single D-type flip-flop with clock enable and synchronous reset.
- When clock enable (CE) is High and synchronous reset (R) is not asserted, the data on the data input (D) of
this design element is transferred to the corresponding data output (Q) during the
clock (C) transition.
- When R is active, it overrides all other inputs and resets the data output
(Q) Low upon the next clock transition.
- When CE is Low, clock transitions are ignored.
This flip-flop is asynchronously initialized when power is applied.
When global set/reset (GSR) is active upon power-up or when asserted via the STARTUP block,
the value of the INIT attribute is placed on the register's output.
Logic Table
Inputs |
Outputs |
R |
CE |
D |
C |
Q |
1 |
X |
X |
↑ |
0 |
0 |
0 |
X |
X |
No Change |
0 |
1 |
D |
↑ |
D |
Port Descriptions
Port |
Direction |
Width |
Function |
C |
Input |
1 |
Clock input. Polarity is determined by the IS_C_INVERTED attribute. |
CE |
Input |
1 |
Active-High register clock enable. |
D |
Input |
1 |
Data input |
Q |
Output |
1 |
Data output |
R |
Input |
1 |
Synchronous reset. Polarity is determined by the IS_R_INVERTED attribute. |
Design Entry Method
Instantiation |
Yes |
Inference |
Recommended |
IP and IP Integrator Catalog |
No |
Available Attributes
Attribute |
Type |
Allowed Values |
Default |
Description |
INIT |
BINARY |
1'b0, 1'b1 |
1'b0 |
Sets the initial value of Q output after configuration or when GSR is asserted via the STARTUP block. |
Programmable Inversion Attributes: Specifies whether or not to use the optional inversion on specific pins for this component to change the
active polarity of the pin function. When set to 1 on a clock pin (C), it creates a negative edge register.
When set to 1 on other pins, it changes the function to behave active-Low rather than active-High.
If an external inverter is specified on one of these associated pins, the Vivado Design Suite will automatically
set this attribute during the opt_design stage so that additional logic is not necessary for changing the
input polarity.
|
IS_C_INVERTED |
BINARY |
1'b0 to 1'b1 |
1'b0 |
Specifies whether or not to use the optional inversion for the C pin of this component. |
IS_D_INVERTED |
BINARY |
1'b0 to 1'b1 |
1'b0 |
Specifies whether or not to use the optional inversion for the D pin of this component. Must be set to 0 unless used as an I/O register. |
IS_R_INVERTED |
BINARY |
1'b0 to 1'b1 |
1'b0 |
Specifies whether or not to use the optional inversion for the R pin of this component. |
VHDL Instantiation Template
Unless they already exist, copy the following
two statements and paste them before the entity declaration.
Library UNISIM;
use UNISIM.vcomponents.all;
-- FDRE: D Flip-Flop with Clock Enable and Synchronous Reset
-- Versal Prime series
-- Xilinx HDL Language Template, version 2021.1
FDRE_inst : FDRE
generic map (
INIT => '0', -- Initial value of register, '0', '1'
-- Programmable Inversion Attributes: Specifies the use of the built-in programmable inversion
IS_C_INVERTED => '0', -- Optional inversion for C
IS_D_INVERTED => '0', -- Optional inversion for D
IS_R_INVERTED => '0' -- Optional inversion for R
)
port map (
Q => Q, -- 1-bit output: Data
C => C, -- 1-bit input: Clock
CE => CE, -- 1-bit input: Clock enable
D => D, -- 1-bit input: Data
R => R -- 1-bit input: Synchronous reset
);
-- End of FDRE_inst instantiation
Verilog Instantiation Template
// FDRE: D Flip-Flop with Clock Enable and Synchronous Reset
// Versal Prime series
// Xilinx HDL Language Template, version 2021.1
FDRE #(
.INIT(1'b0), // Initial value of register, 1'b0, 1'b1
// Programmable Inversion Attributes: Specifies the use of the built-in programmable inversion
.IS_C_INVERTED(1'b0), // Optional inversion for C
.IS_D_INVERTED(1'b0), // Optional inversion for D
.IS_R_INVERTED(1'b0) // Optional inversion for R
)
FDRE_inst (
.Q(Q), // 1-bit output: Data
.C(C), // 1-bit input: Clock
.CE(CE), // 1-bit input: Clock enable
.D(D), // 1-bit input: Data
.R(R) // 1-bit input: Synchronous reset
);
// End of FDRE_inst instantiation
Related Information
-
Versal ACAP Register Reference
Manual (AM012)