get_hw_sio_gts - 2020.2 English

Get list of hardware SIO GTs.

Syntax

get_hw_sio_gts [‑of_objects <args>] [‑regexp] [‑nocase] [‑filter <arg>]
    [‑quiet] [‑verbose] [<patterns>]

Returns

hardware SIO GTs

Usage

Name	Description
`[-of_objects]`	Get 'hw_sio_gt' objects of these types: 'hw_server hw_target hw_device hw_sio_ibert hw_sio_gtgroup hw_sio_pll hw_sio_tx hw_sio_rx hw_sio_link'.
`[-regexp]`	Patterns are full regular expressions
`[-nocase]`	Perform case-insensitive matching. (valid only when -regexp specified)
`[-filter]`	Filter list with expression
`[-quiet]`	Ignore command errors
`[-verbose]`	Suspend message limits during command execution
`[<patterns>]`	Match the 'hw_sio_gt' objects against patterns. Default: *

Description

Returns the Gigabit Transceiver objects (GTs), hw_sio_gt, that are in use on the IBERT debug core on the current hardware device.

The customizable LogiCORE™ IP Integrated Bit Error Ratio Tester (IBERT) core for Xilinx® FPGAs is designed for evaluating and monitoring the Gigabit Transceivers (GTs). The IBERT core enables in-system serial I/O validation and debug, letting you measure and optimize your high-speed serial I/O links in your FPGA-based system. Refer to the LogiCORE IP Integrated Bit Error Ratio Tester (IBERT) for 7 Series GTX Transceivers v3.0 (PG132)or to 7 Series FPGAs GTX/GTH Transceivers User Guide (UG476) or UltraScale Architecture GTH Transceivers User Guide (UG576) for more information.

Using the IBERT debug core you can configure and tune the GT transmitters and receivers through the Dynamic Reconfiguration Port (DRP) port of the GTX transceiver. This lets you change property settings on the GTs, as well as registers that control the values on the ports.

This command returns a list of GT objects on the IBERT debug core, or returns an error if it fails.

Arguments

-of_objects <arg> - (Optional) Return the GT objects of the specified hw_server, hw_target, hw_device, hw_sio_ibert, hw_sio_pll, hw_sio_tx, hw_sio_rx, or hw_sio_link. The objects must be specified with an appropriate get_hw_* command.

Note: The -of_objects option requires objects to be specified using the get_* commands, such as get_cells or get_pins, rather than specifying objects by name. In addition, -of_objects cannot be used with a search <pattern>.

-regexp - (Optional) Specifies that the search <patterns> are written as regular expressions. Both search <patterns> and -filter expressions must be written as regular expressions when this argument is used. Xilinx regular expression Tcl commands are always anchored to the start of the search string. You can add ".*" to the beginning or end of a search string to widen the search to include a substring. See http://perldoc.perl.org/perlre.html for help with regular expression syntax.

Note: The Tcl built-in command regexp is not anchored, and works as a standard Tcl command. For more information refer to http://www.tcl.tk/man/tcl8.5/TclCmd/regexp.htm.

-nocase - (Optional) Perform case-insensitive matching when a pattern has been specified. This argument applies to the use of -regexp only.

-filter <args> - (Optional) Filter the results list with the specified expression. The -filter argument filters the list of objects returned by get_hw_sio_gts based on property values on the GT objects. You can find the properties on an object with the report_property or list_property commands. In the case of the "hw_sio_gt" object, "NAME" and "GT_TYPE" are two of the properties that can be used to filter results.

The filter search pattern should be quoted to avoid having to escape special characters that may be found in net, pin, or cell names, or other properties. String matching is case-sensitive and is always anchored to the start and to the end of the search string. The wildcard “*” character can be used at the beginning or at the end of a search string to widen the search to include a substring of the property value.

Note: The filter returns an object if a specified property exists on the object, and the specified pattern matches the property value on the object. In the case of the "*" wildcard character, this will match a property with a defined value of "".

For string comparison, the specific operators that can be used in filter expressions are "equal" (==), "not-equal" (!=), "match" (=~), and "not-match" (!~). Numeric comparison operators <, >, <=, and >= can also be used. Multiple filter expressions can be joined by AND and OR (&& and ||). The following gets input pins that do NOT contain the “RESET” substring within their name:

get_pins * -filter {DIRECTION == IN && NAME !~ "*RESET*"}

Boolean (bool) type properties can be directly evaluated in filter expressions as true or not true:

-filter {IS_PRIMITIVE && !IS_LOC_FIXED}

-quiet - (Optional) Execute the command quietly, returning no messages from the command. The command also returns TCL_OK regardless of any errors encountered during execution.

Note: Any errors encountered on the command-line, while launching the command, will be returned. Only errors occurring inside the command will be trapped.

-verbose - (Optional) Temporarily override any message limits and return all messages from this command.

Note: Message limits can be defined with the set_msg_config command.

<patterns> - (Optional) Match hw_sio_gt objects against the specified patterns. The default pattern is the wildcard '*' which gets a list of all hw_hw_sio_gts available on the current debug core.

Example

The following example gets the GTs assigned to the defined communication links on the IBERT debug core:

get_hw_sio_gts -of_objects [get_hw_sio_links]