DSPCPLX - 2020.2 English - UG1483

This block is listed in the following Xilinx Blockset libraries: Index, DSP.

The Xilinx DSPCPLX block is one of the advanced features provided by Versal™ architecture DSP, which is the optimized solution to deal with 18x18 complex multiplication followed by 58 + 58 accumulation operation.

Versal architecture DSP supports an 18-bit complex multiplier with two back-to-back DSP58s in the same tile pair together. The two DSP58s with their DSP_MODE attributes set to CINT18 form one complex arithmetic unit. The right DSP58 computes the real result P_RE and left computes the imaginary result P_IM. The following figure shows the unisim DSPCPLX primitive which is used to develop this feature.

Figure 1. Unisim DSPCPLX Primitive

Block Parameters

The block parameters dialog box can be invoked by double-clicking the icon in your Simulink model.

Basic tab

Parameters specific to the Basic tab are as follows:

Input Configuration

A or ACIN input

Specifies if the A input should be taken directly from the a_re, a_im ports or from the cascaded acin_re, acin_im ports. The acin_re and acin_im ports can only be connected to another DSPCPLX block.

B or BCIN input

Specifies if the B input should be taken directly from the b_re, b_im ports or from the cascaded bcin_re, bcin_im ports. The bcin_re and bcin_im ports can only be connected to another DSPCPLX block.

Pattern Detection on Real Output

Reset p_re register on pattern detection

If selected and the pattern_re is detected, reset the p_re register on the next cycle

AUTO RESET PRIORITY RE

When enabled by selecting the option above, select RESET (the default) or CEP (clock enabled for the P_RE (output) resister).

Pattern Input RE

Pattern Input from c_re port

When selected, the pattern_re used in pattern detection on Real Output is read from the c_re port.

Using Pattern Attribute RE (58-bit hex value)

Value is used in pattern detection logic which is best described as an equality check on the output of the adder/subtractor/logic unit.

Using Pattern Attribute RE (58-bit hex value)

Enter a 58-bit value that is used in the pattern detector.

Mask Input RE

Mask input from c_re port

When selected, the mask_re used in pattern detection is read from the c_re port.

Using Mask Attribute RE (58-bit hex value)

Enter a 58-bit value used to mask out certain bits during pattern detection on Real Output.

MODE1

Selects rounding_mode 1 (C_RE-bar left shifted by 1).

MODE2

Selects rounding_mode 2 (C_RE-bar left shifted by 2).

Pattern Detection on Imaginary Output

Reset p_im register on pattern detection

If selected and the pattern_im is detected, reset the p_im register on the next cycle.

AUTO RESET PRIORITY IM

When enabled by selecting the option above, select RESET (the default) or CEP (clock enabled for the P_IM (output) resister).

Mask Input IM

Mask input from c_im port

When selected, the mask_im used in pattern detection on Imaginary Output is read from the c_im port.

Using Mask Attribute RE (58-bit hex value)

Enter a 58-bit value used to mask out certain bits during pattern detection on Imaginary Output.

MODE1

Selects rounding_mode 1 (C_IM-bar left shifted by 1).

MODE2

Selects rounding_mode 2 (C_IM-bar left shifted by 2).

Optional Ports tab

Parameters specific to the Optional Ports tab are as follows:

Input Ports

Consolidate control port

When selected, combines the opmode, alumode, carry_in, carry_in_sel, inmode and conjugate ports into one 18-bit port. Bits 0 to 8 are the opmode, bits 9 to 12 are the alumode port, bit 13 is the carry_in port, bits 14 to 16 are the carry_in_sel port, bit 17 is the Conjugate_A input port and bit 18 is the Conjugate_B port. This option should be used when the Opmode block is used to generate a DSPCPLX instruction.

Note: Enabling this option will drive both the left and right dsp58 tiles with the same configuration.

Provide c port

When selected, the c_re and c_im ports are made available. Otherwise, the c_re and c_im ports are tied to '0'.

Provide global reset port

When selected, the port rst_all is made available. This port is connected to all available reset ports based on the pipeline selections.

Provide global enable port

When selected, the optional en_all port is made available. This port is connected to all available enable ports based on the pipeline selections.

Cascadable Ports

Provide pcin port

When selected, the pcin_re and pcin_im ports are exposed. The pcin_re and pcin_im ports must be connected to the pcout_re and pcout_im ports of another DSPCPLX block respectively.

Provide carry cascade in port

When selected, the carrycascin_re and carrycascin_im ports are exposed. These ports can only be connected to a carry cascade out ports of another DSPCPLX block.

Provide multiplier sign cascade in port

When selected, the multsignin_re and multsignin_im ports are exposed. These ports can only be connected to a multiplier sign cascade out ports of another DSPCPLX block.

Output Ports

Provide carryout port

When selected, the carryout_re and carryout_im output ports are made available.

Provide pattern detect port

When selected, the patterndetect_re and patterndetect_out ports are provided. When the pattern_re/pattern_im, either from the mask_re/mask_im or the c_re/c_im register is matched, the respective patterndetect_re/patterndetect_im port is set to '1'.

Provide pattern bar detect port

When selected, the patternbdetect_re and patternbdetect_im ports are provided. When the inverse of the pattern_re/pattern_im, either from the mask_re/mask_im or the c_re/c_im register is matched, the patternbdetect_re/patternbdetect_im port is set to '1'.

Provide overflow port

When selected, the overflow_re and overflow_im ports are provided. These ports indicate when the operation in the DSPCPLX has overflowed beyond the bit P_RE[N]/P_IM[N] where N is between 0 and 56. N is determined by the number of 1s in the mask_re/mask_im whether set by the GUI mask field or the c_re/c_im port input.

Provide underflow port

When selected, the underflow_re and underflow_im ports are provided. These ports indicate when the operation in the DSPCPLX has underflowed. Underflow occurs when the number goes below -P_RE[N]/P_IM[N], where N is determined by the number of 1s in the mask_re/mask_im whether set by the GUI mask field or the c_re/c_im port input.

Cascadable Ports

Provide acout port

When selected, the acout_re and acout_im output ports are made available. The acout_re/acout_im port must be connected to the acin_re/acin_im port of another DSPCPLX block.

Provide bcout port

When selected, the bcout_re and bcout_im output ports are made available. The bcout_re/bcout_im port must be connected to the bcin_re/bcin_im port of another DSPCPLX block.

Provide pcout port

When selected, the pcout_re and pcout_im output ports are made available. The pcout_re/pcout_im port must be connected to the pcin_re/pcin_im port of another DSPCPLX block.

Provide multiplier sign cascade out port

When selected, the multsignout_re and multsignout_im ports are made available. These ports can only be connected to the multsignin_re and multsignin_im ports of another DSPCPLX block respectively and is used to support 116-bit accumulators/adders and subtracters which are built from two DSPCPLXs.

Provide carry cascade out port

When selected, the carrycascout_re and carrycascout_im ports are made available. These ports can only be connected to the carrycascin_re and carrycascin_im ports of another DSPCPLX block respectively.

Pipelining tab

Parameters specific to the Pipelining tab are as follows:

Length of a_re/acin_re pipeline

Specifies the length of the pipeline on input register A_RE. The pipeline of length 0 removes the register on the input.

Length of a_im/acin_im pipeline

Specifies the length of the pipeline on input register A_IM. The pipeline of length 0 removes the register on the input.

Length of b_re/bcin_re pipeline

Specifies the length of the pipeline for the b_re input and whether it is read from b_re or bcin_re.

Length of b_im/bcin_im pipeline

Specifies the length of the pipeline for the b_im input and whether it is read from b_im or bcin_im.

Length of acout_re pipeline

Specifies the length of the pipeline between the a_re/acin_re input and the acout_re output port. The pipeline of length 0 removes the register from the acout_re pipeline length. Must be less than or equal to the length of the a_re/acin_re pipeline.

Length of acout_im pipeline

Specifies the length of the pipeline between the a_im/acin_im input and the acout_im output port. The pipeline of length 0 removes the register from the acout_im pipeline length. Must be less than or equal to the length of the a_im/acin_im pipeline.

Length of bcout_re pipeline

Specifies the length of the pipeline between the b_re/bcin_re input and the bcout_re output port. The pipeline of length 0 removes the register from the bcout_re pipeline length. Must be less than or equal to the length of the b_re/bcin_re pipeline.

Length of bcout_im pipeline

Specifies the length of the pipeline between the b_im/bcin_im input and the bcout_im output port. The pipeline of length 0 removes the register from the bcout_im pipeline length. Must be less than or equal to the length of the b_im/bcin_im pipeline.

Pipeline c_re

Indicates whether the input from the c_re port should be registered.

Pipeline c_im

Indicates whether the input from the c_im port should be registered.

Pipeline p_re

Indicates whether the outputs p_re and pcout_re should be registered.

Pipeline p_im

Indicates whether the outputs p_im and pcout_im should be registered.

Pipeline multiplier_re

Indicates whether the internal multiplier_re should register its output.

Pipeline multiplier_im

Indicates whether the internal multiplier_im should register its output.

Pipeline opmode_re

Indicates whether the opmode_re port should be registered.

Pipeline opmode_im

Indicates whether the opmode_im port should be registered.

Pipeline alumode_re

Indicates whether the alumode_re port should be registered.

Pipeline alumode_im

Indicates whether the alumode_im port should be registered.

Pipeline carry in Re

Indicates whether the carryin_re port should be registered.

Pipeline carry in Im

Indicates whether the carryin_im port should be registered.

Pipeline carry in select Re

Indicates whether the carryinsel_re port should be registered.

Pipeline carry in select Im

Indicates whether the carryinsel_im port should be registered.

Pipeline preadder output register ad

Indicates to add a pipeline register to the ad output.

Pipeline Conjugate register A

Indicates to add a pipeline register to the Conjugate_A input.

Pipeline Conjugate register B

Indicates to add a pipeline register to the Conjugate_B input.

Reset/Enable Ports tab

Parameters specific to the Reset/Enable tab are as follows:

Provide Reset Ports

Reset port for a/acin

When selected, rsta_re and rsta_im ports are made available. This resets the pipeline registers for port a_re, a_im when set to '1'.

Reset port for b/bcin

When selected, rstb_re and rstb_im are made available. This resets the pipeline registers for port b_re, b_im when set to '1'.

Reset port for c

When selected, rstc_re and rstc_im are made available. This resets the pipeline registers for port c_re, c_im when set to '1'.

Reset port for multiplier

When selected, rstm_re and rstm_im are made available. This resets the pipeline registers for internal multiplier respectively when set to '1'.

Reset port for P

When selected, rstp_re and rstp_im are made available. This resets the output p_re and p_im registers when set to '1'.

Reset port for carry in

When selected, rstallcarryin_re and rstallcarryin_im are made available. This resets the pipeline registers for carryin_re and carryin_im port when set to '1'.

Reset port for alumode

When selected, rstalumode_re and rstalumode_im are made available. This resets the pipeline register for the alumode_re and alumode_im port when set to '1'.

Reset port for controls (opmode and carry_in_sel)

When selected, a port rstctrl_re and rstctrl_im are made available. This resets the pipeline register for the opmode_re/opmode_im register (if available) and the carryinsel_re/carryinsel_im register (if available) when set to '1'.

Reset port for ad

When selected, port rstad is made available. This resets the pipeline ad register for ports when set to '1'.

Reset port for Conjugate_a

When selected, port rstconjugate_a is made available. This resets the pipeline register for the Conjugate_a port when set to '1'.

Reset port for Conjugate_b

When selected, port rstconjugate_b is made available. This resets the pipeline register for the Conjugate_b port when set to '1'.

Provide Enable Ports

Enable port for first a/acin register

When selected, enable ports cea1_re and cea1_im for the first a_re and a_im pipeline register are made available.

Enable port for second a/acin register

When selected, enable ports cea2_re and cea2_im for the second a_re and a_im pipeline registers are made available.

Enable port for first b/bcin register

When selected, enable ports ceb1_re and ceb1_im for the first b_re and b_im pipeline registers are made available.

Enable port for second b/bcin register

When selected, enable ports ceb2_re and ceb2_im for the second b_re and b_im pipeline registers are made available.

Enable port for c

When selected, enable ports cec_re and cec_im for the port C_re and C_im registers are made available.

Enable port for multiplier

When selected, enable ports cem_re and cem_im for the Real and Imaginary multiplier registers are made available.

Enable port for p

When selected, enable ports cep_re and cep_im for the port P_re and P_im output registers are made available.

Enable port for carry in

When selected, enable ports cecarryin_re and cecarryin_im for the Real and Imaginary carry in registers are made available.

Enable port for alumode

When selected, enable ports cealumode_re and cealumode_im for the Real and Imaginary alumode registers are made available.

Enable port for controls (opmode and carry_in_sel)

When selected, enable ports cectrl_re and cectrl_im are made available. The ports cectrl_re and cectrl_im controls the Real and Imaginary opmode and carry in select registers.

Enable port for ad

When selected, an enable port is created for the preadder output register ad.

Enable port for Conjugate_a

When selected, an enable port conjugate_a is added for the Conjugate_A register.

Enable port for Conjugate_b

When selected, an enable port conjugate_b is added for the Conjugate_B register.

Inversion Options tab

When the checkbox is selected on this tab, the specified signal is inverted.

Implementation tab

Parameters specific to the Implementation tab are as follows.

Use synthesizable model

When selected, the DSPCPLX is implemented from an RTL description which might not map directly to the DSP58 hardware. This is useful if a design using the DSPCPLX block is targeted at device families that do not contain DSP58 hardware primitives.

Other parameters used by this block are explained in the topic Common Options in Block Parameter Dialog Boxes.